POWER MIRROR CONTROL SYSTEM(w/ Memory) Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

DESCRIPTION

The main body ECU (multiplex network body ECU) receives the retractable outer mirror switch signal from the outer mirror switch assembly (retractable outer mirror switch). The main body ECU then sends the mirror retract/return signal to each outer mirror control ECU assembly via CAN communication. Based on this signal, each outer mirror control ECU assembly retracts or returns the outer rear view mirror assembly.

WIRING DIAGRAM

A00073EE29

CAUTION / NOTICE / HINT

Note

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Use the GTS to check if the CAN communication system is functioning normally Click here.

      OK
      CAN communication DTCs are not output.

    NG

    GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) Click here

    OK

  2. READ VALUE USING GTS (RETRACTABLE OUTER MIRROR SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Outer Mirror Fold SW Retractable outer mirror switch signal / ON or OFF

      ON: Retractable outer mirror switch in retract position

      OFF: Retractable outer mirror switch in driving position

      		 -
      OK
      On the GTS screen, ON or OFF is displayed for each item according to the above.

    NG

    INSPECT RETRACTABLE OUTER MIRROR SWITCH Click here

    OK

  3. PERFORM ACTIVE TEST USING GTS (MIRROR RETRACT FUNCTION)


    1. Enter the following menus: Body Electrical / Mirror L or Mirror R / Active Test.

    2. Perform the Active Test according to the display on the GTS.

      Mirror L / Mirror R
      Tester Display Test Part Control Range Diagnostic Note
      Mirror Fold/Return Mirror retract operation Fold / Return

      • Operate with power switch on (IG) and the vehicle stopped.

      • This test activates the Fold / Return.

      • This operation can be confirmed by watching the mirror move in the desired direction.
      Result
      Result Proceed to
      Outer rear view mirror assemblies operate normally A
      Outer rear view mirror assembly (front passenger door) does not operate normally B
      Outer rear view mirror assembly (driver door) does not operate normally C

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) Click here

    B

  4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)


    1. A0003PYE01
      Text in Illustration
      *1 (A) Forward Position
      *2 (B)
      *3 (C) Driving Position
      *4 (D)
      *5 (E) Retracted Position
      *a

      Component without harness connected

      (Outer Rear View Mirror Assembly (Front Passenger Door))

      Remove the outer rear view mirror assembly (front passenger door) Click here.

    2. When checking each mirror position, set the mirror position by hand. Apply auxiliary battery voltage and check the mirror movement.

      Note


      • Disconnect and reconnect the auxiliary battery for each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      OK
      Measurement Condition Mirror Position Specified Condition

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Forward position (A) Moves from (A) to (E)

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Forward position (A) Does not move

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Between forward position (A) and driving position (C) Moves from (B) to (E)

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Between forward position (A) and driving position (C) Moves from (B) to (A)

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Driving position (C) Moves from (C) to (E)

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Driving position (C) Does not move

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Between driving position (C) and retracted position (E) Moves from (D) to (E)

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Between driving position (C) and retracted position (E) Moves from (D) to (C)

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Retracted position (E) Does not move

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Retracted position (E) Moves from (E) to (C)

    OK

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) Click here

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) Click here

  5. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)


    1. A0004ZXE01
      Text in Illustration
      *1 (A) Forward Position
      *2 (B)
      *3 (C) Driving Position
      *4 (D)
      *5 (E) Retracted Position
      *a

      Component without harness connected

      (Outer Rear View Mirror Assembly (Driver Door))

      Remove the outer rear view mirror assembly (driver door) Click here.

    2. When checking each mirror position, set the mirror position by hand. Apply auxiliary battery voltage and check the mirror movement.

      Note


      • Disconnect and reconnect the auxiliary battery for each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      OK
      Measurement Condition Mirror Position Specified Condition

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Forward position (A) Moves from (A) to (E)

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Forward position (A) Does not move

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Between forward position (A) and driving position (C) Moves from (B) to (E)

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Between forward position (A) and driving position (C) Moves from (B) to (A)

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Driving position (C) Moves from (C) to (E)

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Driving position (C) Does not move

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Between driving position (C) and retracted position (E) Moves from (D) to (E)

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Between driving position (C) and retracted position (E) Moves from (D) to (C)

      Auxiliary battery positive (+) → Terminal 3 (MR)

      Auxiliary battery negative (-) → Terminal 11 (MF)

      		 Retracted position (E) Does not move

      Auxiliary battery negative (-) → Terminal 3 (MR)

      Auxiliary battery positive (+) → Terminal 11 (MF)

      		 Retracted position (E) Moves from (E) to (C)

    OK

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) Click here

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) Click here

  6. INSPECT RETRACTABLE OUTER MIRROR SWITCH


    1. A0007ZME35
      Text in Illustration
      *a

      Component without harness connected

      (Retractable Outer Mirror Switch)
      *b Driving position
      *c Retract position
      *d AUTO position

      Remove the retractable outer mirror switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (MR) - 4 (E) Except retract position Below 1 Ω
      2 (MR) - 4 (E) Retract position 10 kΩ or higher

    NG

    REPLACE RETRACTABLE OUTER MIRROR SWITCH Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (RETRACTABLE OUTER MIRROR SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    1. Disconnect the H9 connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H72-2 (MR) - H9-28 (RET) Always Below 1 Ω
      H72-2 (MR) - Body ground Always 10 kΩ or higher
      H72-4 (E) - Body ground Always 10 kΩ or higher

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR