Click here

LUGGAGE DOOR HINGE TORSION BAR INSTALLATION

Click here
Click here Click here

CAUTION / NOTICE / HINT

Note:

After installing the torsion bar, use your hand to open and close the luggage door. Make sure the luggage door can open and close smoothly.

Click here

PROCEDURE


  1. Click here

    INSTALL LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT


    1. A0003LD

      Install a new luggage compartment door torsion bar support as shown in the illustration.

  2. Click here

    INSTALL LUGGAGE DOOR HINGE TORSION BAR RH


    1. Check the identification mark on the luggage door hinge torsion bar RH.

      w/o Power Trunk Lid System
      White
      w/ Power Trunk Lid System
      Yellow
    2. A0004AHE04

      Set the tip of the luggage door hinge torsion bar RH in the center installation hole. The upper and lower installation holes are used for adjustment.

      Table 1. Text in Illustration
      *a Installation Hole
      *b Installation Hole (For Adjustment)
    3. A0005AK

      Connect the luggage door hinge torsion bar RH to the left side of the vehicle body as shown in the illustration.

    4. A0005Q1E04

      Using SST, install the luggage door hinge torsion bar RH to the luggage door hinge and the right side of the vehicle body as shown in the illustration.

      09804-24010
    5. A0008DB

      Connect the luggage door hinge torsion bar RH to the luggage compartment door torsion bar support as shown in the illustration.

  3. Click here

    INSTALL LUGGAGE DOOR HINGE TORSION BAR LH


    1. Check the identification mark on the luggage door hinge torsion bar RH.

      w/o Power Trunk Lid System
      White
      w/ Power Trunk Lid System
      Yellow
    2. A0006GZE04

      Set the tip of the luggage door hinge torsion bar LH in the center installation hole. The upper and lower installation holes are used for adjustment.

      Table 2. Text in Illustration
      *a Installation Hole
      *b Installation Hole (For Adjustment)
    3. A0009AL

      Connect the luggage door hinge torsion bar LH to the right side of the vehicle body as shown in the illustration.

    4. A00050PE04

      Using SST, install the luggage door hinge torsion bar LH to the luggage door hinge and the left side of the vehicle body as shown in the illustration.

      09804-24010
    5. A0007A8

      Connect the luggage door hinge torsion bar LH to the luggage compartment door torsion bar support as shown in the illustration.

    6. A0004ML

      Engage the 2 claws as shown in the illustration.

  4. Click here

    INSTALL LUGGAGE CLOSER MOTOR ASSEMBLY (w/ Power Trunk Lid System)

    Click here

  5. Click here

    INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER LH

    Click here

  6. Click here

    INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH

    Click here

  7. Click here

    INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. Install the 3 clips.

    2. Engage the 2 fasteners and install the luggage compartment inner trim cover LH.

  8. Click here

    INSTALL ROPE HOOK (for LH Side)


    1. A0006HO

      Engage the 2 claws and install the rope hook.

  9. Click here

    INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. Engage the guide.

    2. Install the luggage hold belt striker assembly with the bolt.

  10. Click here

    INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH (w/ Power Trunk Lid System)

    Click here

  11. Click here

    INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH (w/o Power Trunk Lid System)


    1. Install the 3 clips.

    2. Engage the 2 fasteners and install the luggage compartment inner trim cover RH.

  12. Click here

    INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH (w/ Power Trunk Lid System)


    1. Install the 2 clips.

    2. Engage the 4 fasteners and install the luggage compartment inner trim cover RH.

  13. Click here

    INSTALL ROPE HOOK (for RH Side)


    1. A0006EZ

      Engage the 2 claws and install the rope hook.

  14. Click here

    INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)


    1. Engage the guide.

    2. Install the luggage hold belt striker assembly with the bolt.

  15. Click here

    INSTALL LUGGAGE COMPARTMENT FRONT TRIM COVER


    1. Engage the 8 fasteners and install the luggage compartment front trim cover.

  16. Click here

    INSTALL REAR FLOOR FINISH PLATE


    1. Engage the 4 clips and install the rear floor finish plate.

    2. Install the 3 clips.

  17. Click here

    INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)


    1. Engage the 2 guides.

    2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.

  18. Click here

    INSTALL SPARE WHEEL COVER PAD RH


    1. Install the spare wheel cover pad RH.

  19. Click here

    INSTALL SPARE WHEEL COVER PAD LH


    1. Install the spare wheel cover pad LH.

  20. Click here

    INSTALL LUGGAGE COMPARTMENT FLOOR MAT


    1. Install the luggage compartment floor mat.

  21. Click here

    INSTALL LUGGAGE COMPARTMENT DOOR COVER

    Click here

  22. Click here

    INSTALL LUGGAGE COMPARTMENT DOOR ASSIST GRIP

    Click here

  23. Click here

    INSTALL LUGGAGE COMPARTMENT DOOR INSIDE HANDLE

    Click here

  24. Click here

    INSTALL LUGGAGE LOCK CONTROL CABLE PLATE

    Click here

  25. Click here

    INITIALIZE POWER TRUNK LID SYSTEM (w/ Power Trunk Lid System)

    (Click here)

  26. Click here

    INSPECT POWER TRUNK LID OPERATION (w/ Power Trunk Lid System)

    (Click here)