Click here

POWER WINDOW CONTROL SYSTEM Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH

Click here
Click here
DTC Code DTC Name
  Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH
Click here

DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the fail-safe mode may be functioning.

If power window initialization (Click here) has not been performed, the auto up and down functions will not operate.

Tip:

If the pulse sensor built into the power window regulator motor assembly (for rear RH door) malfunctions, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly (for RH door) at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly (for RH door).

Table 1. *a from Main Body ECU (Multiplex Network Body ECU) *b Rear Power Window Regulator Switch Assembly (for RH Door) *c Power Window Regulator Motor Assembly (for Rear RH Door) *d LIN Communication Line
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

  • If the power window regulator motor assembly (for rear RH door) has been replaced with a new one, initialize the power window control system (Click here).

Click here

PROCEDURE


  1. Click here

    READ VALUE USING GTS (RR-DOOR MOTOR)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / RR-Door Motor / Data List.

    5. Read the Data List according to the display on the GTS.

      Table 2. RR-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Door P/W Auto SW Rear RH door power window auto switch signal / ON or OFF

      ON: Rear RH door power window auto switch being operated

      OFF: Rear RH door power window auto switch not being operated

      		 -
      OK
      On the GTS screen, ON or OFF is displayed accordingly.

  2. Click here

    PERFORM INITIALIZATION (FOR REAR RH DOOR)


    1. Initialize the power window regulator motor assembly (for rear RH door) (Click here).


  3. Click here

    CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)


    1. Check that the rear RH door power window moves when the auto up and down functions of the rear power window regulator switch assembly (for RH door) are operated (Click here).

      OK
      Rear RH door auto up and down functions are normal.

    • OK

      END (PROBLEM DUE TO INITIALIZATION FAILURE)

    • NG

      REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) (Click here)

  4. Click here

    INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)


    1. A00053JE03

      Remove the rear power window regulator switch assembly (for RH door) (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      8 (AUTO) - 1 (GND) Auto up or auto down position Below 1 Ω
      Table 3. Text in Illustration
      *a

      Component without harness connected

      (Rear Power Window Regulator Switch Assembly (for RH Door))

  5. Click here

    CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH (FOR RH DOOR) - WINDOW REGULATOR MOTOR (FOR REAR RH DOOR))


    1. Disconnect the N2 power window regulator motor assembly (for rear RH door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N4-8 (AUTO) - N2-4 (AUTO) Always Below 1 Ω
      N4-8 (AUTO) - Body ground Always 10 kΩ or higher
      N2-4 (AUTO) - Body ground Always 10 kΩ or higher

    • OK

      REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) (Click here)

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR