Click here

POWER WINDOW CONTROL SYSTEM Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

Click here
Click here
DTC Code DTC Name
  Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch
Click here

DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the fail-safe mode may be functioning.

If power window initialization (Click here) has not been performed, the auto up and down functions will not operate.

Tip:

If the pulse sensor built into the power window regulator motor assembly (for front passenger door) malfunctions, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly.

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

  • If the power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system (Click here).

Click here

PROCEDURE


  1. Click here

    READ VALUE USING GTS (P-DOOR MOTOR)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / P-Door Motor / Data List.

    5. Read the Data List according to the display on the GTS.

      Table 1. P-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door P/W Auto SW Front passenger door power window auto switch signal / ON or OFF

      ON: Front passenger door power window auto switch being operated

      OFF: Front passenger door power window auto switch not being operated

      		 -
      OK
      On the GTS screen, ON or OFF is displayed accordingly.

  2. Click here

    PERFORM INITIALIZATION (FOR FRONT PASSENGER DOOR)


    1. Initialize the power window regulator motor assembly (for front passenger door) (Click here).


  3. Click here

    CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)


    1. Check that the front passenger door power window moves when the auto up and down functions of the power window regulator switch assembly are operated (Click here).

      OK
      Front passenger door auto up and down functions are normal.

    • OK

      END (PROBLEM DUE TO INITIALIZATION FAILURE)

    • NG

      REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)

  4. Click here

    INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    1. A00053JE03

      Remove the power window regulator switch assembly (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      8 (AUTO) - 1 (GND) Auto up or auto down position Below 1 Ω
      Table 2. Text in Illustration
      *a

      Component without harness connected

      (Power Window Regulator Switch Assembly)

  5. Click here

    CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR (FOR FRONT PASSENGER DOOR))


    1. Disconnect the L9*1 or M8*2 power window regulator motor assembly (for front passenger door) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 3. for LHD
      Tester Connection Condition Specified Condition
      L4-8 (AUTO) - L9-4 (AUTO) Always Below 1 Ω
      L4-8 (AUTO) - Body ground Always 10 kΩ or higher
      L9-4 (AUTO) - Body ground Always 10 kΩ or higher
      Table 4. for RHD
      Tester Connection Condition Specified Condition
      M13-8 (AUTO) - M8-4 (AUTO) Always Below 1 Ω
      M13-8 (AUTO) - Body ground Always 10 kΩ or higher
      M8-4 (AUTO) - Body ground Always 10 kΩ or higher

    • OK

      REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR