ROOF HEADLINING REMOVAL

Info Added 2017-08-02

PROCEDURE


  1. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  3. REMOVE REAR SEAT ASSEMBLY

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B001VBJ

      Disengage the 10 claws and remove the front door scuff plate LH.

  5. REMOVE COWL SIDE TRIM BOARD LH


    1. B001VK1

      Remove the clip.

    2. Disengage the claw and clip, and remove the cowl side trim board LH.

  6. REMOVE FRONT DOOR OPENING TRIM COVER LH


    1. B001VF7

      Disengage the 3 claws and remove the front door opening trim cover LH.

  7. REMOVE FRONT PILLAR GARNISH LH


    1. B001VBHE04
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

      Tech Tips

      Make the front pillar garnish LH hang from the front pillar garnish clip.

    2. B001VJ7E05

      While pushing the tabs of the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.

    3. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. B001VBZE04
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.

  8. REMOVE REAR DOOR SCUFF PLATE LH


    1. B001VJL

      Disengage the 8 claws and remove the rear door scuff plate LH.

  9. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. B001VG1

      Disengage the 2 claws and 2 guides.

    2. Disengage the 5 clips and remove the center pillar lower garnish LH.

  10. REMOVE CENTER PILLAR UPPER GARNISH LH


    1. B001VHT

      Remove the 2 clips.

    2. B001VHM

      Disengage the clip as shown in the illustration.

    3. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.

  11. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

  13. REMOVE FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  14. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  15. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  16. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  17. REMOVE CENTER PILLAR UPPER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  18. REMOVE REAR SEAT SIDE GARNISH LH


    1. B001VFW

      Disengage the 5 claws and remove the rear seat side garnish LH.

  19. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. B001VH6

      Disengage the 4 clips.

    2. Disengage the 2 guides and remove the roof side inner garnish assembly LH.

  20. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  22. REMOVE LOWER SHIFT LEVER ASSEMBLY

    Click here

  23. REMOVE INSTRUMENT PANEL SAFETY PAD

    Click here

  24. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/o Pre-crash Safety System)

    Click here

  25. REMOVE PROTECTOR (w/o Pre-crash Safety System)

    Click here

  26. REMOVE PROTECTOR (w/ Pre-crash Safety System)

    Click here

  27. REMOVE RAIN SENSOR COVER (w/o Pre-crash Safety System)

    w/ Rain Sensor: Click here

  28. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  29. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  30. REMOVE ROOF CONSOLE BOX ASSEMBLY

    Click here

  31. REMOVE SPOT LIGHT ASSEMBLY

    Click here

  32. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side.


    1. B001VHNE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B001VC7

      Disengage the 2 clips and remove the assist grip sub-assembly.

    3. Remove the 2 clips from the vehicle body.

  33. REMOVE REAR ASSIST GRIP ASSEMBLY LH


    1. B001VCQE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B001VIA

      Disengage the 2 clips and remove the rear assist grip assembly LH.

    3. Remove the 2 clips from the vehicle body.

  34. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  35. REMOVE VISOR BRACKET COVER (for LH Side)


    1. B001VD3

      Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.

  36. REMOVE VISOR ASSEMBLY LH


    1. B001VF8

      Remove the 2 screws and visor assembly LH.

  37. REMOVE VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  38. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  39. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedure for the other visor holder.


    1. B001VHIE05
      Text in Illustration
      *a 45°

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

  40. REMOVE ROOF HEADLINING ASSEMBLY


    1. for Windshield Glass Side:


      1. Disconnect each connector.

    2. Disconnect the connector from the sliding roof drive gear sub-assembly.

      B001VFPE05
      Text in Illustration
      *A w/o Roof Antenna *B w/ Roof Antenna
      *1 Clamp *2 Fastener
      *3 Guide - -
      *a Front Pillar LH *b Front Pillar RH
      *c Rear Pillar RH *d Sliding Roof Drive Gear Sub-assembly

    3. Disengage the 3 clamps and disconnect the 2 connectors from the front pillar LH.

    4. Disengage the 2 clamps from the front pillar RH.

    5. w/o Roof Antenna:


      1. Disengage the clamp and disconnect the connector from the rear pillar RH.

    6. w/ Roof Antenna:


      1. Disengage the clamp and disconnect the 2 connectors from the rear pillar RH.

    7. Disengage the 12 claws and 8 fasteners.

    8. Slide the roof headlining assembly to disengage the 3 clips and guide as shown in the illustration.

      Tech Tips

      Leave the 3 clips installed to the vehicle.

    9. B001VFU

      Remove the roof headlining assembly from the vehicle through the rear door as shown in the illustration.

      Note

      Do not damage the roof headlining assembly or vehicle interior.

    10. B001VJJ

      Remove the 3 clips from the vehicle body as shown in the illustration.

  41. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the front door opening trim weatherstrip LH.

    2. Remove any residual weatherstrip sealant from the vehicle body using cleaner.

      Note

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  42. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  43. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip LH.

    2. Remove any residual weatherstrip sealant from the vehicle body using cleaner.

      Note

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  44. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.