DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Turn Light RH | Turn signal switch (right) status/ ON or OFF |
ON: Turn signal switch (right) on OFF: Turn signal switch (right) off |
- |
| Turn Light LH | Turn signal switch (left) status/ ON or OFF |
ON: Turn signal switch (left) on OFF: Turn signal switch (left) off |
- |
| PCS OFF Switch | - | - | This item is displayed on the GTS but is not used. |
| PCS Indicator | "Pre-crash Safety System Malfunction Visit Your Dealer" display request signal/ ON or OFF |
ON: "Pre-crash Safety System Malfunction Visit Your Dealer" display requested OFF: "Pre-crash Safety System Malfunction Visit Your Dealer" display not requested |
- |
| PCS Disabled Indicator | "Pre-crash Safety System Unavailable" display request signal/ ON or OFF |
ON: "Pre-crash Safety System Unavailable" display requested OFF: "Pre-crash Safety System Unavailable" display not requested |
- |
| Pre-Collision Safety Warning Buz | Pre-crash safety system warning buzzer/ Valid or Inval |
Valid: Pre-crash safety system warning buzzer operation possible Inval: Pre-crash safety system warning buzzer operation not possible |
- |
| Pre-Collision Brake | Pre-crash safety brake function/ Valid or Inval |
Valid: Pre-crash safety brake operation possible Inval: Pre-crash safety brake operation not possible |
- |
| Pre-Collision Safety Brake Ind | Pre-crash safety system "BRAKE!" alert status/ ON or OFF |
ON: Pre-crash safety system "BRAKE!" alert on OFF: Pre-crash safety system "BRAKE!" alert off |
- |
| PBA Start | Pre-crash safety brake assist activation signal/ ON or OFF |
ON: Pre-crash safety brake assist activated OFF: Pre-crash safety brake assist not activated |
Signal status changes when the pre-crash safety brake assist is activated before a crash (Pre-crash safety brake will activate only in situations where the driver depresses the brake pedal) |
| Warning Brake | Warning brake activation signal/ ON or OFF |
ON: Warning brake activated OFF: Warning brake not activated |
- |
| Brake Assist Standby | Supplemental brake pressure signal/ ON or OFF |
ON: Supplemental brake pressure being provided OFF: Supplemental brake pressure not being provided |
Signal status changes when supplemental brake pressure is being provided after a crash is judged as unavoidable and before the brake pedal is depressed |
| Pre-Collision Brake Control | Pre-crash safety brake operational status/ ON or OFF |
ON: Pre-crash safety brake operating OFF: Pre-crash safety brake not operating |
Status changes when pre-crash safety brake operates before a crash |
| AVS Start | AVS control activation status/ ON or OFF |
ON: AVS control activated OFF: AVS control not activated |
Not Supported |
| VGRS Start | VGRS control activation status/ ON or OFF |
ON: VGRS control activated OFF: VGRS control not activated |
Not Supported |
| PBA Control | Pre-crash safety brake assist operational status/ Valid or Invalid |
Valid: Pre-crash safety brake assist control operation possible Invalid: Pre-crash safety brake assist control operation not possible |
- |
| PCS Crash Alarm Buzzer | Skid control buzzer status/ ON or OFF |
ON: Skid control buzzer sounds OFF: Skid control buzzer does not sound |
- |
| Front Radar-Dirt History | Millimeter wave radar sensor assembly dirt history/ ON or OFF |
ON: History of excessive dirt OFF: No history of excessive dirt |
- |
| Front Radar-Temperature Malfunction History | Millimeter wave radar sensor assembly abnormal temperature history/ ON or OFF |
ON: History of abnormal temperature OFF: No history of abnormal temperature |
- |
| Front Radar-Low Voltage History | Millimeter wave radar sensor assembly low voltage history/ ON or OFF |
ON: History of low voltage OFF: No history of low voltage |
- |
| Front Radar-Incorrect Axial Gap (Vertical) History | Millimeter wave radar sensor assembly vertical misalignment history/ ON or OFF |
ON: History of vertical misalignment OFF: No history of vertical misalignment |
- |
| Front Radar-Incorrect Axial Gap (Horizontal) History | Millimeter wave radar sensor assembly horizontal misalignment history/ ON or OFF |
ON: History of horizontal misalignment OFF: No history of horizontal misalignment |
- |
| Front Recognition Camera-Blockage History | Forward recognition camera obstruction history/ ON or OFF |
ON: History of being obstructed OFF: No history of being obstructed |
- |
| Front Recognition Camera-Malfunction History | Forward recognition camera malfunction history (abnormal temperature, low voltage, DTC stored, etc.)/ ON or OFF |
ON: History of malfunction OFF: No history of malfunction |
- |
| Driving Support ECU Destination | Destination country for driving support computer/ JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX |
Actual country code | - |
| Control Mode | ECU control mode status/ Normal or Check |
Normal: Normal operation Check: Operating in Control Mode |
- |
| PCS Operation State Retention Setting | Displays the setting of the PCS Operation State Retention Setting customize setting/ ON or OFF |
ON: PCS Operation State Retention Setting customize setting is set to ON OFF: PCS Operation State Retention Setting customize setting is set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 1 | Displays the setting of the PCS Alarm Activation Distance Retention Setting 1 customize setting ON or OFF |
ON: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to ON OFF: PCS Alarm Activation Distance Retention Setting 1 customize setting is set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 2 | Displays the setting of the PCS Alarm Activation Distance Retention Setting 2 customize setting/ ON or OFF |
ON: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to ON OFF: PCS Alarm Activation Distance Retention Setting 2 customize setting is set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 3 | Displays the setting of the PCS Alarm Activation Distance Retention Setting 3 customize setting/ ON or OFF |
ON: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to ON OFF: PCS Alarm Activation Distance Retention Setting 3 customize setting is set to OFF |
- |
| The Number of DTCs | Number of past trouble codes/min: 0, max: 255 | Number of DTCs will be displayed | - |
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch status/ ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Stop Light Relay Output | STPO terminal output condition/ ON or OFF |
ON: Output OFF: Not output |
- |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus:
for Pre-Collision: Body Electrical / Pre-Crash 2 / Active Test.
for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Active Test.
for Combination Meter: Body Electrical / Combination Meter / Active Test.
Perform Active Test according to the display on the GTS.
Tech Tips
The power switch must be turned on (IG) to proceed with the Active Test using the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Crash Alarm Buzzer | Skid control buzzer assembly | ON / OFF | Test possible with power switch on (IG), vehicle stopped |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop lights | ON / OFF | Test possible at vehicle speed of 0 km/h (0 mph) |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Precrash | PCS OFF warning light | ON / OFF | - |