Click here

KNEE AIRBAG ASSEMBLY(for Driver Side) INSTALLATION

Click here
Click here Click here

PROCEDURE


  1. Click here

    INSTALL TIRE PRESSURE WARNING RESET SWITCH (for LHD)

    Click here

  2. Click here

    INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A00062DE04

      Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

      Table 1. Text in Illustration
      *a Airbag Connector
      *b Airbag Connector Lock
      Note:

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the airbag connector lock to install the airbag connector.

    5. Engage the 2 claws to connect the DLC3.

    6. Connect the connector and engage the clamp to install the wire harness.

    7. Engage the 2 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.

    8. Install the 4 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
      Note:

      Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  3. Click here

    INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A0008P8E02

      Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

      Table 2. Text in Illustration
      *1 No. 1 Interior Illumination Light Assembly
      *a Airbag Connector
      *b Airbag Connector Lock
      *c DLC3
      Note:

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the airbag connector lock to install the airbag connector.

    5. Engage the 2 claws to connect the DLC3.

    6. Engage the 2 claws to connect the No. 1 interior illumination light assembly.

    7. Engage the 2 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.

    8. Install the 4 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
      Note:

      Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  4. Click here

    INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    Click here

  5. Click here

    CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    Click here

  6. Click here

    INSTALL INSTRUMENT SIDE PANEL

    for LHD Driver Side: (Click here)

    for RHD Driver Side: (Click here)

  7. Click here

    INSTALL FRONT DOOR OPENING TRIM COVER

    for LHD Driver Side: (Click here)

    for RHD Driver Side: (Click here)

  8. Click here

    INSTALL COWL SIDE TRIM BOARD

    for LHD Driver Side: (Click here)

    for RHD Driver Side: (Click here)

  9. Click here

    INSTALL FRONT DOOR SCUFF PLATE

    for LHD Driver Side: (Click here)

    for RHD Driver Side: (Click here)

  10. Click here

    INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

    Click here

  11. Click here

    CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  12. Click here

    INSTALL LUGGAGE TRIM SERVICE HOLE COVER

    Click here

  13. Click here

    PERFORM DIAGNOSTIC SYSTEM CHECK

    (Click here)

  14. Click here

    INSPECT SRS WARNING LIGHT

    (Click here)

  15. Click here

    INSPECT TIRE PRESSURE WARNING SYSTEM

    (Click here)

  16. Click here

    PERFORM INITIALIZATION

    (Click here)