SPIRAL CABLE REMOVAL

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column)

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)

    Click here

  5. REMOVE LOWER NO. 3 STEERING WHEEL COVER

    Click here

  6. REMOVE LOWER NO. 2 STEERING WHEEL COVER

    Click here

  7. REMOVE HORN BUTTON ASSEMBLY

    Click here

  8. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  9. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  10. REMOVE LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  11. REMOVE LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  12. REMOVE UPPER STEERING COLUMN COVER

    Click here

  13. REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the power switch on (IG).

    • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the front wheels are aligned facing straight ahead.

    4. A0009PQE01
      Text in Illustration
      *a Slider

      Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    5. Disconnect the other connector from the spiral cable with sensor sub-assembly.

    6. A00064Y

      Disengage the 3 claws to remove the spiral cable with sensor sub-assembly.

  14. REMOVE SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly or the steering sensor.

    • Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in the center position of the steering sensor becoming misaligned. Therefore, make sure to use the lock pin provided with a new spiral cable sub-assembly when removing the steering sensor from the spiral cable sub-assembly.

    • When replacing the steering sensor: Click here


    1. A0008L7

      Install the lock pin to the steering sensor.

      Note


      • Use the lock pin provided with a new spiral cable sub-assembly.

      • Do not remove the lock pin before installing the steering sensor to the spiral cable sub-assembly.

    2. A0003UXE05
      Text in Illustration
      *a Guide

      Disengage the 6 claws and 2 pins, and remove the spiral cable sub-assembly from the steering sensor.

      Note

      Do not damage the pins of the spiral cable sub-assembly and guides of the steering sensor.