Click here

AIRBAG SYSTEM, Diagnostic DTC:B1835/58, B1836/58, B1837/58, B1838/58

Click here
Click here Click here
DTC Code DTC Name
B1835/58 Short in Curtain Shield Squib LH Circuit
B1836/58 Open in Curtain Shield Squib LH Circuit
B1837/58 Short to GND in Curtain Shield Squib LH Circuit
B1838/58 Short to B+ in Curtain Shield Squib LH Circuit
Click here

DESCRIPTION

The curtain shield squib LH circuit consists of the airbag sensor assembly and curtain shield airbag assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1835/58

  • The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit during primary check.

  • Curtain shield squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Curtain shield airbag assembly LH (Curtain shield squib LH)

  • Airbag sensor assembly
B1836/58

  • The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit.

  • Curtain shield squib LH malfunction

  • Airbag sensor assembly malfunction
B1837/58

  • The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH circuit.

  • Curtain shield squib LH malfunction

  • Airbag sensor assembly malfunction
B1838/58

  • The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit.

  • Curtain shield squib LH malfunction

  • Airbag sensor assembly malfunction
Table 1. *a Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH) *b Airbag Sensor Assembly
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

Tip:

  • Perform the simulation method by selecting check mode (Signal Check) using the GTS (Click here).

  • After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK CONNECTORS


    1. A00042UE05

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the curtain shield airbag assembly LH and airbag sensor assembly.

      OK
      The connectors are properly connected.
      Tip:

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the curtain shield airbag assembly LH and airbag sensor assembly.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the floor wire connector (on the curtain shield airbag assembly LH side) is not damaged.

      OK
      The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    7. Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

      OK
      The short spring is not deformed or damaged.
      Table 2. Text in Illustration
      *1 Curtain Shield Airbag Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire

  2. Click here

    CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)


    1. A0004KDE02

      Connect the connector to the airbag sensor assembly.

    2. Connect SST (resistance 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the curtain shield airbag assembly LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note:

      • Do not forcibly insert SST into the terminals of the connector when connecting it.

      • Insert SST straight into the terminals of the connector.

      09843-18061

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory (Click here).

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs (Click here).

      OK
      DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.
      Tip:

      Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Disconnect SST from connector C.

      Table 3. Text in Illustration
      *1 Curtain Shield Airbag Assembly LH
      *2 Airbag Sensor Assembly
      *a

      Front view of wire harness connector

      (to Curtain Shield Airbag Assembly LH)

  3. Click here

    CHECK FLOOR WIRE


    1. A0008GVE02

      Disconnect the floor wire from the airbag sensor assembly.

    2. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) auxiliary battery terminal.

      2. Turn the power switch on (IG).

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        P16-1 (ICL+) - Body ground Power switch on (IG) Below 1 V
        P16-2 (ICL-) - Body ground Power switch on (IG) Below 1 V

      4. Turn the power switch off.

      5. Disconnect the cable from the negative (-) auxiliary battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check for an open in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        P16-1 (ICL+) - P16-2 (ICL-) Always Below 1 Ω

    4. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        P16-1 (ICL+) - Body ground Always 1 MΩ or higher
        P16-2 (ICL-) - Body ground Always 1 MΩ or higher

    5. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B (Click here).

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        P16-1 (ICL+) - P16-2 (ICL-) Always 1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

        Table 4. Text in Illustration
        *1 Curtain Shield Airbag Assembly LH
        *2 Airbag Sensor Assembly
        *3 Floor Wire
        *a

        Front view of wire harness connector

        (to Curtain Shield Airbag Assembly LH)

  4. Click here

    CHECK DTC


    1. A0004AWE12

      Connect the connectors to the curtain shield airbag assembly LH and airbag sensor assembly.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory (Click here).

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs (Click here).

      OK
      DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.
      Tip:

      Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

      Table 5. Text in Illustration
      *1 Curtain Shield Airbag Assembly LH
      *2 Airbag Sensor Assembly