Click here

METER / GAUGE SYSTEM, Diagnostic DTC:B1507, B1508

Click here
Click here
DTC Code DTC Name
B1507 Open in Turn Signal Circuit
B1508 Short in Turn Signal / Hazard Flasher Circuit
Click here

DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No. DTC Detection Condition Trouble Area
B1507

When IG voltage is 9.5 V or more and the following condition is detected:


  • Open in turn signal light circuit

  • LED

  • Bulb

  • Harness or connector

  • Instrument panel junction block assembly

  • Outer mirror control ECU assembly LH*

  • Outer mirror control ECU assembly RH*

  • Combination meter assembly
B1508

When IG voltage is 9.5 V or more and the following condition is detected:


  • Short in turn signal light circuit or hazard warning light circuit

  • LED

  • Bulb

  • Harness or connector

  • Instrument panel junction block assembly

  • Outer mirror control ECU assembly LH*

  • Outer mirror control ECU assembly RH*

  • Combination meter assembly

Click here

WIRING DIAGRAM


Click here
  1. A0006NSE06

    w/ Seat Position Memory

  2. A0003N5E04

    w/o Seat Position Memory

Click here

CAUTION / NOTICE / HINT

Note:

Inspect the LEDs and bulbs for this system before performing the following inspection procedure (See page for Side Turn Signal Light Assembly,Click herefor Rear Combination Light Assembly).

Click here

PROCEDURE


  1. Click here

    INSPECT LIGHTS


    1. Inspect the illumination of each turn signal light.

      Result
      Result Proceed to
      Turn signal lights for one side do not illuminate. A
      Front turn signal light does not illuminate. B
      Rear turn signal light does not illuminate. C
      Side turn signal light does not illuminate (w/o Seat Position Memory). D
      Side turn signal light does not illuminate (w/ Seat Position Memory). E

  2. Click here

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the H13 combination meter assembly connector.

    2. Disconnect the 3A instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Table 1. for LH
      Tester Connection Condition Specified Condition
      H13-13 (LL) - 3A-20 Always Below 1 Ω
      Table 2. for RH
      Tester Connection Condition Specified Condition
      H13-7 (LR) - 3A-37 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Table 3. for LH
      Tester Connection Condition Specified Condition
      H13-13 (LL) - Body ground Always 10 kΩ or higher
      Table 4. for RH
      Tester Connection Condition Specified Condition
      H13-7 (LR) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      NG A
      OK B

    • A

      REPAIR OR REPLACE HARNESS OR CONNECTOR

    • BClick here
  3. Click here

    CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the A69*1 or A74*2 headlight assembly connector.


      • *1: for LH

      • *2: for RH

    2. Disconnect the 3D instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Table 5. for LH
      Tester Connection Condition Specified Condition
      A69-1 (B) - 3D-10 Always Below 1 Ω
      A69-2 (E) - Body ground Always Below 1 Ω
      Table 6. for RH
      Tester Connection Condition Specified Condition
      A74-1 (B) - 3D-5 Always Below 1 Ω
      A74-2 (E) - Body ground Always Below 1 Ω
      Standard Resistance (Check for Short)
      Table 7. for LH
      Tester Connection Condition Specified Condition
      A69-1 (B) - Body ground Always 10 kΩ or higher
      Table 8. for RH
      Tester Connection Condition Specified Condition
      A74-1 (B) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      NG A
      OK B

    • A

      REPAIR OR REPLACE HARNESS OR CONNECTOR

    • BClick here
  4. Click here

    CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the U13*1 or U12*2 rear combination light assembly connector.


      • *1: for LH

      • *2: for RH

    2. Disconnect the 3C instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Table 9. for LH
      Tester Connection Condition Specified Condition
      U13-5 (TRN) - 3C-22 Always Below 1 Ω
      U13-6 (E) - Body ground Always Below 1 Ω
      Table 10. for RH
      Tester Connection Condition Specified Condition
      U12-5 (TRN) - 3C-19 Always Below 1 Ω
      U12-6 (E) - Body ground Always Below 1 Ω
      Standard Resistance (Check for Short)
      Table 11. for LH
      Tester Connection Condition Specified Condition
      U13-5 (TRN) - Body ground Always 10 kΩ or higher
      Table 12. for RH
      Tester Connection Condition Specified Condition
      U12-5 (TRN) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      NG A
      OK B

    • A

      REPAIR OR REPLACE HARNESS OR CONNECTOR

    • BClick here
  5. Click here

    CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the M6*1 or L7*2 side turn signal light assembly connector.


      • *1: for LH

      • *2: for RH

    2. Disconnect the 3A or 3B instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Table 13. for LH
      Tester Connection Condition Specified Condition
      M6-16 (B) - 3A-40 Always Below 1 Ω
      M6-12 (-) - Body ground Always Below 1 Ω
      Table 14. for RH
      Tester Connection Condition Specified Condition
      L7-16 (B) - 3B-32 Always Below 1 Ω
      L7-12 (-) - Body ground Always Below 1 Ω
      Standard Resistance (Check for Short)
      Table 15. for LH
      Tester Connection Condition Specified Condition
      M6-16 (B) - Body ground Always 10 kΩ or higher
      Table 16. for RH
      Tester Connection Condition Specified Condition
      L7-16 (B) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      NG A
      OK B

    • A

      REPAIR OR REPLACE HARNESS OR CONNECTOR

    • BClick here
  6. Click here

    CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the M9*1 or L10*2 outer mirror control ECU assembly connector.


      • *1: for LH

      • *2: for RH

    2. Disconnect the 3A or 3B instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Table 17. for LH
      Tester Connection Condition Specified Condition
      M9-11 (TRNI) - 3A-40 Always Below 1 Ω
      M9-7 (GND) - Body ground Always Below 1 Ω
      Table 18. for RH
      Tester Connection Condition Specified Condition
      L10-11 (TRNI) - 3B-32 Always Below 1 Ω
      L10-7 (GND) - Body ground Always Below 1 Ω
      Standard Resistance (Check for Short)
      Table 19. for LH
      Tester Connection Condition Specified Condition
      M9-11 (TRNI) - Body ground Always 10 kΩ or higher
      Table 20. for RH
      Tester Connection Condition Specified Condition
      L10-11 (TRNI) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      NG A
      OK B

    • A

      REPAIR OR REPLACE HARNESS OR CONNECTOR

    • BClick here
  7. Click here

    INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. A0008LCE02

      Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).

      Table 21. Text in Illustration
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    2. Front turn signal light


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        for LH
        Tester Connection Condition Specified Condition
        3A-20 - 3D-10 Always Below 1 Ω
        for RH
        Tester Connection Condition Specified Condition
        3A-37 - 3D-5 Always Below 1 Ω
        Result
        Result Proceed to
        NG A
        OK B

    3. Rear turn signal light


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        for LH
        Tester Connection Condition Specified Condition
        3A-20 - 3C-22 Always Below 1 Ω
        for RH
        Tester Connection Condition Specified Condition
        3A-37 - 3C-19 Always Below 1 Ω
        Result
        Result Proceed to
        NG A
        OK B

    4. Side turn signal light


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        for LH
        Tester Connection Condition Specified Condition
        3A-20 - 3A-40 Always Below 1 Ω
        for RH
        Tester Connection Condition Specified Condition
        3A-37 - 3B-32 Always Below 1 Ω
        Result
        Result Proceed to
        NG A
        OK (w/o Seat Position Memory) B
        OK (for LH with Seat Position Memory) C
        OK (for RH with Seat Position Memory) D

  8. Click here

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH


    1. Replace the outer mirror control ECU assembly LH with a new or known good one (Click here).

    2. Recheck for DTCs (Click here).

      Result
      Result Proceed to
      DTCs are not output. A
      DTCs are output. B

    • A

      END

    • B

      REPLACE COMBINATION METER ASSEMBLY (Click here)

  9. Click here

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH


    1. Replace the outer mirror control ECU assembly RH with a new or known good one (Click here).

    2. Recheck for DTCs (Click here).

      Result
      Result Proceed to
      DTCs are not output. A
      DTCs are output. B

    • A

      END

    • B

      REPLACE COMBINATION METER ASSEMBLY (Click here)