METER / GAUGE SYSTEM ON-VEHICLE INSPECTION

PROCEDURE


  1. INSPECT COMBINATION METER ASSEMBLY


    1. Check speedometer operation.

      Note


      • The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

      • The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform this inspection after confirming that no DTCs are output from the brake control system.

      • If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.


      1. Before starting the following inspection, check if brake control system DTCs are output.

      2. Check the values by referring to the table below.

        ABS/VSC/TRC
        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Vehicle Speed Maximum wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
        Reference (except RHD without rear fog light)
        GTS Indication (km/h) Acceptable Range (km/h)
        20 21.0 to 25.0
        40 41.7 to 46.2
        60 62.7 to 67.2
        80 83.4 to 88.4
        100 104.3 to 109.3
        120 125.1 to 130.6
        140 145.8 to 151.8
        160 166.2 to 173.2
        180 186.9 to 194.5
        200 207.7 to 215.7
        220 228.4 to 236.8
        240 249.2 to 258.0
        Reference (for RHD without rear fog light)
        GTS Indication (km/h) Acceptable Range (km/h)
        20 20.5 to 24.5
        40 41.0 to 45.5
        60 61.5 to 66.0
        80 82.1 to 87.1
        100 102.6 to 106.6
        120 123.1 to 128.1
        140 143.6 to 148.6
        160 164.1 to 169.1
        180 184.6 to 189.6
        200 205.1 to 210.1
        220 225.7 to 230.7
        240 246.2 to 251.2

    2. Inspect tachometer


      1. Connect the GTS, and start the engine.

      2. Compare the test results with the tachometer indication.

        GTS Indication (rpm)

        Acceptable Range (rpm)

        Data in ( ) is for Reference
        700 630 to 770
        1000 (900 to 1100)
        2000 (1850 to 2150)
        3000 2800 to 3200
        4000 (3800 to 4200)
        5000 4800 to 5200
        6000 (5750 to 6250)
        7000 6700 to 7300

    3. Check LED illumination (LED check)


      1. Check the illumination function of the warning or indicator lights listed below when turning the power switch on (IG).

        OK
        Warning or Indicator Light Specified Condition
        Master Warning light comes on for about 3 seconds after turning the power switch on (IG).
        Tire pressure
        PCS*
        Headlight leveling
        SRS Warning light comes on for about 6 seconds after turning the power switch on (IG).
        Charge Warning light comes on when turning the power switch on (IG).
        EPS
        MIL (Check engine warning light)
        Brake

        • Warning or indicator light comes on for about 3 seconds after turning the power switch on (IG).

        • Warning or indicator light comes on when turning the power switch from off to on (READY) for 3 seconds, then goes off.
        Slip
        ABS
        VSC OFF
        Electronically controlled brake

        • *: w/ Pre-crash safety system