LIGHTING SYSTEM CUSTOMIZE PARAMETERS

PROCEDURE

1. Click here

   CUSTOMIZE LIGHTING SYSTEM (INT)

   
   

   1. Customizing using the GTS

      Tip:

      The following items can be customized.

      Note:
      

      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.

      
      

      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Illuminated Entry.

      5. Select the setting by referring to the table below.

         Table 1. Illuminated Entry

         Tester Display	Default	Content	Setting	Relevant ECU
         Lighting Time	15 s	Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)	15 s, 7.5 s or 30 s	Main body ECU (Multiplex network body ECU)
         I/L when ACC OFF	ON	Lights up the following lights when the power switch is turned from on (ACC or IG) to off: Power Switch illumination Roof Console Box Assembly (Front Interior Light) Spot Light Assembly (Rear Interior Light)	ON or OFF	Main body ECU (Multiplex network body ECU)
         I/L ON W/Door Key Unlock	ON	Lights up the following lights when doors are unlocked using a mechanical key or door control transmitter: Power Switch illumination Roof Console Box Assembly (Front Interior Light) Spot Light Assembly (Rear Interior Light) No. 1 Interior Illumination Light Assembly (Front Footwell Lights) No. 1 Interior Illumination Light Assembly (Rear Footwell Lights) Front Door Trim Board Sub-assembly (Front Door Ambient Lights)*1 Rear Door Trim Board Sub-assembly (Rear Door Ambient Lights)*1 Interior Illumination Light Sub-assembly (Instrument Panel Ambient Light)*1	ON or OFF	Main body ECU (Multiplex network body ECU)
         Room Light when Aprchd	ON	Lights up the following lights when a key enters any actuation area around the doors: Power Switch illumination Roof Console Box Assembly (Front Interior Light) Spot Light Assembly (Rear Interior Light)	ON or OFF	Main body ECU (Multiplex network body ECU)
         Inside Foot Light	ON	Lights up the following lights: No. 1 Interior Illumination Light Assembly (Front Footwell Lights) No. 1 Interior Illumination Light Assembly (Rear Footwell Lights)	ON or OFF	Main body ECU (Multiplex network body ECU)
         Light Control	ON	Dims (ON setting) or turns off (OFF setting) the following lights when all of the following conditions are met: Condition Power switch is on (IG) The shift lever is moved out of P. All doors are closed. Lights that operate No. 1 Interior Illumination Light Assembly (Front Footwell Lights) No. 1 Interior Illumination Light Assembly (Rear Footwell Lights) Front Door Trim Board Sub-assembly (Front Door Ambient Lights)*1 Rear Door Trim Board Sub-assembly (Rear Door Ambient Lights)*1 Interior Illumination Light Sub-assembly (Instrument Panel Ambient Light)*1	ON or OFF	Main body ECU (Multiplex network body ECU)
         Interior Light Control	ON	Lights up the following lights when the illuminated entry function is operating: Power Switch illumination Roof Console Box Assembly (Front Interior Light) Spot Light Assembly (Rear Interior Light) No. 1 Interior Illumination Light Assembly (Front Footwell Lights) No. 1 Interior Illumination Light Assembly (Rear Footwell Lights) Front Door Trim Board Sub-assembly (Front Door Ambient Lights)*1 Rear Door Trim Board Sub-assembly (Rear Door Ambient Lights)*1 Interior Illumination Light Sub-assembly (Instrument Panel Ambient Light)*1	ON or OFF	Main body ECU (Multiplex network body ECU)
         Interior Illumination Light*2	ON	Lights up the following lights: Front Door Trim Board Sub-assembly (Front Door Ambient Lights) Rear Door Trim Board Sub-assembly (Rear Door Ambient Lights) Interior Illumination Light Sub-assembly (Instrument Panel Ambient Light)	ON or OFF	Main body ECU (Multiplex network body ECU)

         
         

         • *1: w/ Ambient Light

   2. Customizing using the multi-display (w/ multi-display)

      
      

      1. Turn the power switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle customization / Light Settings.

      3. Select the setting by referring to the table below:

         Table 2. Light Settings

         Display	Default	Content	Setting	Relevant ECU
         Interior lights off timer	15 sec.	Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)	Off, 15 sec., 7.5 sec., or 30 sec.	Main body ECU (Multiplex network body ECU)

   3. Customizing using the combination meter assembly (w/o multi-display)

      Tip:
      

      • Press and hold the DISP switch (steering pad switch assembly) when entering an item.

      • Briefly press the DISP switch (steering pad switch assembly) when selecting an item.

      
      

      1. Turn the power switch on (IG).

      2. Enter the following menus: Settings / Vehicle or Ambient illumin*1

      3. Select the setting by referring to the table below:

         Table 3. Vehicle

         Display	Default	Content	Setting	Relevant ECU
         Interior Lights Off Timer	15 sec.	Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)	Off, 15 sec., 7.5 sec., or 30 sec.	Main body ECU (Multiplex network body ECU)

         Table 4. Ambient illumin*1

         Display	Default	Content	Setting	Relevant ECU
         Ambient illumin (instrument panel)	On	Lights up the following lights: Front Door Trim Board Sub-assembly (Front Door Ambient Lights) Rear Door Trim Board Sub-assembly (Rear Door Ambient Lights) Interior Illumination Light Sub-assembly (Instrument Panel Ambient Light)	On or Off	Main body ECU (Multiplex network body ECU)

         
         

         • *1: w/ Ambient Light

      4. Press and hold the DISP switch (steering pad switch assembly).

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.