Click here

IMMOBILISER SYSTEM, Diagnostic DTC:B2779

Click here
Click here
DTC Code DTC Name
B2779 Engine Starter Communication Malfunction
Click here

DESCRIPTION

If communication between the remote engine starter ECU and certification ECU (smart key ECU assembly) cannot be performed even if a remote engine start operation is performed to try changing the power source mode to on (IG) or start the hybrid control system, this DTC is stored.

When the remote engine starter ECU does not respond to the certification ECU (smart key ECU assembly), this DTC is stored. When communication with the remote engine starter ECU is established and a remote engine start operation is performed, this DTC is cleared.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2779

One of the following conditions is met (1 trip detection logic*):


  • A remote engine start communication error occurs.

  • Response is not possible.

  • Registration has not been performed.

  • Remote engine starter ECU

  • Wire harness or connector

  • Main body ECU (multiplex network body ECU)

  • Certification ECU (smart key ECU assembly)

 A remote engine start operation is performed.

Table 1. Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system does not start with remote engine start operation Hybrid control system cannot be started by remote engine start operation only
Table 2. Related Data List and Active Test
DTC Code Data List and Active Test
B2779

  • Wireless Starter Com ID

  • Wireless C Code
Table 3. *a Remote Engine Starter ECU *b Certification ECU (Smart Key ECU Assembly) *c Option Connector *d Main Body ECU (Multiplex Network Body ECU)
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • When using the GTS with the vehicle power switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Before performing the inspection, check that DTC U0142 is not output.

  • Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to the Service Bulletin.

  • After performing repair, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

Tip:

In this repair manual, only the terminal numbers used for inspection between the main body ECU (multiplex network body ECU) and option connector are listed.

Click here

PROCEDURE


  1. Click here

    READ VALUE USING GTS


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Entry&Start / Data List.

    6. According to the display on the GTS, read the Data List.

      Table 4. Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Wireless C Code Registration status between remote engine starter ECU and certification ECU (smart key ECU assembly)/No Regd or Regd

      No Regd: ID not registered between remote engine starter ECU and certification ECU (smart key ECU assembly)

      Regd: ID registered between remote engine starter ECU and certification ECU (smart key ECU assembly)

      Problems may be caused by the following:


      • Remote engine starter ECU registration has not been performed.

      • Malfunctions in the certification ECU (smart key ECU assembly) or remote engine starter ECU.
      OK
      "Regd" appears on the screen.
      Table 5. Result
      Result Proceed to
      "No Regd" appears on the screen A
      "Regd" appears on the screen B

  2. Click here

    REGISTER REMOTE ENGINE START ID


    1. Register the remote engine start ID.


  3. Click here

    CHECK REMOTE ENGINE START


    1. Check that the hybrid control system can be started using remote engine start operation.

      OK
      Hybrid control system can be started using remote engine start operation.

    • OK

      END (REMOTE ENGINE START ID WAS NOT REGISTERED CORRECTLY)

    • NGClick here
  4. Click here

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - OPTION CONNECTOR)

    Tip:

    In this repair manual, only the terminal numbers used for inspection between the main body ECU (multiplex network body ECU) and option connector are listed.


    1. Disconnect the H10 main body ECU (multiplex network body ECU) connector.

    2. Disconnect the H151 option connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H10-25 (BTX) - H151-7 (BTX) Always Below 1 Ω
      H10-26 (BRX) - H151-3 (BRX) Always Below 1 Ω
      H10-25 (BTX) - Body ground Always 10 kΩ or higher
      H10-26 (BRX) - Body ground Always 10 kΩ or higher

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. Click here

    REPLACE REMOTE ENGINE STARTER ECU


    1. Temporarily replace the remote engine starter ECU with a new one.

    2. Register the remote engine start ID.

    3. Check that the hybrid control system can be started using remote engine start operation.

      OK
      Hybrid control system can be started using remote engine start operation.

    • OK

      END (REMOTE ENGINE STARTER ECU WAS DEFECTIVE)

    • NGClick here
  6. Click here

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    1. Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one (Click here).

    2. Check that the hybrid control system can be started using remote engine start operation.

      OK
      Hybrid control system can be started using remote engine start operation.

    • OK

      END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

    • NG

      REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)