Click here

SMART ENTRY AND START SYSTEM(for Start Function) Power Source Mode does not Change to ON (ACC)

Click here
Click here
DTC Code DTC Name
  Power Source Mode does not Change to ON (ACC)
Click here

DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the power management control ECU receives a signal and changes the power source mode.

Tip:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • When using the GTS with the vehicle power switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

  • Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).

  • If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (Click here).

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • After completing repairs, confirm that the problem does not occur.

Tip:
Table 1. Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (ACC) but does change to on (IG)
  • Power Source Control

  • Power Supply Condition

  • ACC Relay Monitor

 -
Click here

PROCEDURE


  1. Click here

    CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the H2 power management control ECU connector.

    2. Disconnect the 3B instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H2-1 (ACCD) - 3B-23 Always Below 1 Ω
      3B-7 - Body ground Always Below 1 Ω
      H2-1 (ACCD) or 3B-23 - Body ground Always 10 kΩ or higher

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  2. Click here

    INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. A0006LNE02

      Remove the instrument panel junction block assembly (Click here).

      Table 2. Text in Illustration
      *A for LHD *B for RHD
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition

      • 3E-1 - 3B-37*1

      • 3E-1 - 3B-10*1

      • 3F-1 - 3B-37*2

      • 3F-1 - 3B-10*2

      		 Auxiliary battery voltage not applied to terminals 3B-23 and 3B-7 10 kΩ or higher
      Auxiliary battery voltage applied to terminals 3B-23 and 3B-7 Below 1 Ω

      • *1: for LHD

      • *2: for RHD


  3. Click here

    INSPECT POWER MANAGEMENT CONTROL ECU


    1. Reconnect the H2 power management control ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H2-1 (ACCD) - Body ground Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher
      Table 3. Text in Illustration
      *a

      Component with harness connected

      (Power Management Control ECU)

    • OK

      CHECK RELAY CONTACT SIDE CIRCUIT

    • NG

      REPLACE POWER MANAGEMENT CONTROL ECU (Click here)