Click here

SMART ENTRY AND START SYSTEM(for Start Function) Power Source Mode does not Change to ON (IG)

Click here
Click here
DTC Code DTC Name
  Power Source Mode does not Change to ON (IG)
Click here

DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Tip:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

A0008RVE07
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • When using the GTS with the vehicle power switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

  • Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).

  • If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (Click here).

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After completing repairs, confirm that the problem does not occur.

Tip:
Table 1. Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
  • Power Source Control

  • Power Supply Condition

  • IG1 Relay Monitor (Inside)

  • IG2 Relay Monitor (Inside)

  • IG1 Relay Monitor (Outside)

  • IG2 Relay Monitor (Outside)

  • IG1 Circuit

  • IG2 Circuit

 -
Click here

PROCEDURE


  1. Click here

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)


    1. Disconnect the A72 certification ECU (Smart key ECU assembly) connector.

    2. Disconnect the 1C and 1E No. 1 integration relay connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A72-9 (IG2D) - 1C-8 Always Below 1 Ω
      1E-2 - Body ground Always Below 1 Ω
      A72-9 (IG2D) or 1C-8 - Body ground Always 10 kΩ or higher

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  2. Click here

    INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)


    1. Remove the No. 1 integration relay (Click here).

    2. Inspect the No. 1 integration relay (Click here).


  3. Click here

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the H194 certification ECU (Smart key ECU assembly) connector.

    2. Disconnect the 3A and 3B instrument panel junction block assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H194-6 (IG1D) - 3A-27 Always Below 1 Ω
      3B-7 - Body ground Always Below 1 Ω
      H194-6 (IG1D) and 3A-27 - Body ground Always 10 kΩ or higher

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. Click here

    INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2, IG1 NO. 3 AND IG1 NO. 4 RELAY)


    1. Remove the instrument panel junction block assembly (Click here).

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).

    3. A0004GGE02

      Measure the resistance according to the value(s) in the table below.

      Table 2. Text in Illustration
      *A for LHD *B for RHD
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -
      Standard Resistance
      Table 3. for LHD
      Tester Connection Condition Specified Condition

      • 3E-1 - 3D-33

        (IG1 No. 1 relay)

      • 3E-1 - 3D-36

        (IG1 No. 2 relay)

      • 3E-1 - 3C-4

        (IG1 No. 3 relay)

      • 3E-1 - 3C-14

        (IG1 No. 4 relay)

      		 Auxiliary battery voltage not applied to terminals 3A-27 and 3B-7 10 kΩ or higher
      Auxiliary battery voltage applied to terminals 3A-27 and 3B-7 Below 1 Ω
      Table 4. for RHD
      Tester Connection Condition Specified Condition

      • 3F-1 - 3D-33

        (IG1 No. 1 relay)

      • 3F-1 - 3D-36

        (IG1 No. 2 relay)

      • 3F-1 - 3C-4

        (IG1 No. 3 relay)

      • 3F-1 - 3C-14

        (IG1 No. 4 relay)

      		 Auxiliary battery voltage not applied to terminals 3A-27 and 3B-7 10 kΩ or higher
      Auxiliary battery voltage applied to terminals 3A-27 and 3B-7 Below 1 Ω

  5. Click here

    CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    1. A0004N4E01

      Reconnect the A72 and H194 certification ECU (smart key ECU assembly) connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A72-9 (IG2D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher
      H194-6 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher
      Table 5. Text in Illustration
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

    • OK

      CHECK RELAY CONTACT SIDE CIRCUIT

    • NG

      REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)