Click here

SMART ENTRY AND START SYSTEM(for Entry Function) Front Passenger Side Door Entry Lock Function does not Operate

Click here
Click here
DTC Code DTC Name
  Front Passenger Side Door Entry Lock Function does not Operate
Click here

DESCRIPTION

If the entry lock function does not operate for the front passenger door only, but the entry unlock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the front door outside handle assembly (for front passenger door) (lock sensor) (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [lock sensor]).

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

  • When using the GTS with the vehicle power switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.

  • Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).

  • Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).

  • After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

Click here

PROCEDURE


  1. Click here

    CHECK POWER DOOR LOCK CONTROL SYSTEM


    1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

      OK
      Door locks operate normally.

  2. Click here

    READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Data List.

    5. Read the Data List according to the display on the GTS.

      Table 1. Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P-Door Trigger Switch Front passenger door touch sensor (lock sensor) / ON or OFF

      ON: Front passenger door touch sensor (lock sensor) touched

      OFF: Front passenger door touch sensor (lock sensor) not touched

      • Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

      • Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
      OK
      The GTS display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door).

    • OK

      REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    • NGClick here
  3. Click here

    CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU)


    1. Disconnect the L12*1 or M11*2 front door outside handle assembly (for front passenger door) connector.


      • *1: for LHD

      • *2: for RHD

    2. Disconnect the H57 and H58 certification ECU (smart key ECU assembly) connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 2. for LHD
      Tester Connection Condition Specified Condition
      L12-1 (TRG+) - H58-8 (TSW2) Always Below 1 Ω
      H57-1 (E) - Body ground Always Below 1 Ω
      L12-1 (TRG+) or H58-8 (TSW2) - Body ground Always 10 kΩ or higher
      Table 3. for RHD
      Tester Connection Condition Specified Condition
      M11-1 (TRG+) - H58-8 (TSW2) Always Below 1 Ω
      H57-1 (E) - Body ground Always Below 1 Ω
      M11-1 (TRG+) or H58-8 (TSW2) - Body ground Always 10 kΩ or higher

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. Click here

    CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (FRONT PASSENGER DOOR LOCK SENSOR SIGNAL INPUT)


    1. A0006K2E02

      Connect the L12*1 or M11*2 front door outside handle assembly (for front passenger door) connector.


      • *1: for LHD

      • *2: for RHD

      Table 4. Text in Illustration
      *1 Waveform - -
      *a

      Component with harness connected

      (Certification ECU (smart key ECU assembly))

      		 *b In actuality, sampling is being performed

    2. Connect the H57 and H58 certification ECU (smart key ECU assembly) connectors.

    3. Using an oscilloscope, check the waveform.

      OK
      Tester Connection Condition Tool Setting Specified Condition
      H58-8 (TSW2) - H57-1 (E)

      Procedure:


      1. Power switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. All doors closed

      4. Front passenger door lock sensor not touched → touched

      		 2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)

    • OK

      REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    • NG

      REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)