Click here

CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) Check CAN Bus Line for Short to +B (LHD Models)

Click here
Click here
DTC Code DTC Name
  Check CAN Bus Line for Short to +B (LHD Models)
Click here

DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3.

  • Short in CAN main bus line

  • Short in CAN branch line

  • Power management control ECU

  • ECM

  • Main body ECU (Multiplex network body ECU)

  • Combination meter assembly

  • Brake booster with master cylinder assembly (Skid control ECU)

  • Steering sensor

  • Power steering ECU with motor assembly

  • Airbag sensor assembly

  • Air conditioning amplifier assembly

  • Certification ECU (Smart key ECU assembly)

  • Multi-media module receiver assembly*1

  • Clearance warning ECU assembly

  • CAN junction connector LH1

  • CAN junction connector RH1

A0005CYE07
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: Turn the power switch on (IG), turn the cruise control main switch on, turn the blind spot monitor main switch on, wait at least 60 seconds and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 7 seconds or more.

  • After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

  • If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

Tip:

  • Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

  • Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

Click here

PROCEDURE


  1. Click here

    CHECK FOR SHORT TO +B IN CAN BUS LINE (DLC3 BRANCH LINE)


    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    2. A000587E02

      Disconnect the H119 DLC3 branch line connector.

      Table 1. Text in Illustration
      *a

      Rear view of wire harness connector

      (to CAN Junction Connector LH1)
      *b to DLC3
      Note:

      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    3. A0007BJE03

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H29-6 (CANH) - H29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      H29-14 (CANL) - H29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      Table 2. Text in Illustration
      *1 DLC3

    • OKClick here
    • NG

      REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

  2. Click here

    CHECK FOR SHORT TO +B IN CAN BUS LINE


    1. Reconnect the H119 DLC3 branch line connector.

    2. A0007BJE03

      Disconnect the connectors from the CAN junction connector LH1 and CAN junction connector RH1 one at a time.

      Tip:

      Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN junction connector LH1 and CAN junction connector RH1.

      Table 3. Text in Illustration
      *1 DLC3
    3. A00085KE12
      A0008Z6E04
      A0006CBE05

      Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.

      Table 4. Text in Illustration
      *A w/ Navigation System - -
      *1 Clearance Warning ECU Assembly *2 ECM
      *3 Air Conditioning Amplifier Assembly *4 Airbag Sensor Assembly
      *5 Certification ECU (Smart Key ECU assembly) *6 Power Steering ECU with Motor Assembly
      *7 Multi-media Module Receiver Assembly *8 Combination Meter Assembly
      *9 Power Management Control ECU *10 DLC3
      *11 Brake Booster with Master Cylinder Assembly (Skid Control ECU) *12 Steering Sensor
      *13 Main Body ECU (Multiplex Network Body ECU) *14 CAN Junction Connector RH1
      *15 CAN Junction Connector LH1 - -
      Table 5. Text in Illustration
      *a

      Component without harness connected

      (CAN Junction Connector LH1)

      		 - -
      Table 6. Wiring Color
      CAN Junction Connector LH1 Side Code Color (CANH Side) Color (CANL Side)
      CAN main bus line (bus line connecting CAN junction connector LH1 and CAN junction connector RH1) H116 R W
      Combination meter assembly H117 G W
      Main body ECU (Multiplex network body ECU) H118 V W
      DLC3 H119 L W
      Steering sensor H120 P W
      Power management control ECU H130 B W
      Brake booster with master cylinder assembly (Skid control ECU) H131 BE W
      Table 7. Text in Illustration
      *a

      Component without harness connected

      (CAN Junction Connector RH1)

      		 - -
      Table 8. Wiring Color
      CAN Junction Connector RH1 Side Code Color (CANH Side) Color (CANL Side)
      Power steering ECU with motor assembly H121 B W
      CAN main bus line (bus line connecting CAN junction connector LH1 and CAN junction connector RH1) H122 R W
      Air conditioning amplifier assembly H123 G W
      Airbag sensor assembly H124 Y W
      ECM H125 L W
      Certification ECU (Smart key ECU assembly) H127 V W
      Multi-media module receiver assembly*1 H128 BE W
      Clearance warning ECU assembly H132 P W

      *1: w/ Navigation system

      Note:

      Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to +B in 2 or more CAN bus lines.

      Result
      Symptom Proceed to
      The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector. (There is a short to +B in the CAN main bus lines between the CAN junction connector LH1 and CAN junction connector RH1.) A
      The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or more) when a connector is disconnected from the CAN junction connector. (There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.) B

    4. When there is a short to +B in one or more of the bus lines that connect to an ECU (or sensor):


      1. Reconnect all of the connectors to the CAN junction connectors, except for the one that was disconnected last (the bus line that is shorted to +B). Check that the resistance shown on the tester is normal (6 kΩ or more) to confirm that there is a short to +B in the one bus line only.

        Tip:

        • Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

        • Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

    5. When there is no short to +B in any of the bus lines that connect to the ECUs and sensors:


      1. With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN junction connector LH1 and CAN junction connector RH1.


  3. Click here

    CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH1)


    1. A000937E02

      Disconnect the H116 CAN main bus line connector.

      Table 9. Text in Illustration
      *a

      Rear view of wire harness connector

      (to CAN Junction Connector LH1)
      *b to CAN Junction Connector RH1
      Note:

      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    2. A0007BJE03

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H29-6 (CANH) - H29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      H29-14 (CANL) - H29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      Table 10. Text in Illustration
      *1 DLC3

    • OKClick here
    • NG

      REPLACE CAN JUNCTION CONNECTOR LH1

  4. Click here

    CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH1 - CAN J/C RH1)


    1. Reconnect the H116 CAN main bus line connector.

    2. A0006ZAE02

      Disconnect the H122 CAN main bus line connector.

      Table 11. Text in Illustration
      *a

      Rear view of wire harness connector

      (to CAN Junction Connector RH1)
      *b to CAN Junction Connector LH1
      Note:

      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    3. A0007BJE03

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H29-6 (CANH) - H29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      H29-14 (CANL) - H29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      Table 12. Text in Illustration
      *1 DLC3

    • OK

      REPLACE CAN JUNCTION CONNECTOR RH1

    • NG

      REPAIR OR REPLACE CAN MAIN BUS LINE (CAN J/C LH1 - CAN J/C RH1)

  5. Click here

    CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)


    1. Reconnect the connector of the bus line that is shorted to +B to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or more when it was disconnected).

    2. A0007BJE03

      Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the bus line shorted to +B is connected (Click here).

      Table 13. Text in Illustration
      *1 DLC3

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H29-6 (CANH) - H29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      H29-14 (CANL) - H29-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      Tip:

      If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).


    • OK

      REPLACE CORRESPONDING ECU OR SENSOR

    • NG

      REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR