LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2325

DTC Code DTC Name
B2325 LIN Communication Bus Malfunction

DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No. DTC Detection Condition Trouble Area
B2325 Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.

  • Power window regulator motor assembly (for driver door)

  • Power window regulator motor assembly (for front passenger door)

  • Power window regulator motor assembly (for rear RH door)

  • Power window regulator motor assembly (for rear LH door)

  • Multiplex network master switch assembly

  • Sliding roof ECU (sliding roof drive gear sub-assembly)

  • Main body ECU (multiplex network body ECU)

  • Instrument panel junction block assembly

  • Wire harness or connector

WIRING DIAGRAM

A0006KYE15
A0006KYE14

CAUTION / NOTICE / HINT

Note


  • When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it requires initialization Click here.

  • When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization Click here.

  • If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (DRIVER DOOR) - MASTER SWITCH)


    1. Disconnect the M4*1 or L13*2 multiplex network master switch connector.


      • *1: for LHD

      • *2: for RHD

    2. Disconnect the M8*1 or L9*2 power window regulator motor (for driver door) connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      M4-16 (LIN2) - M8-9 (LIN) Always Below 1 Ω
      M4-16 (LIN2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      L13-16 (LIN2) - L9-9 (LIN) Always Below 1 Ω
      L13-16 (LIN2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


    1. A0008QWE02
      Text in Illustration
      *a

      Component without harness connected

      (Multiplex Network Master Switch Assembly)

      Remove the multiplex network master switch assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      16 (LIN2) - 17 (LIN1) Always Below 1 Ω

    NG

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    OK

  3. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly Click here.

      A0008FBE01

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Tech Tips

      This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

      Standard Resistance
      Tester Connection Condition Specified Condition
      3C-26 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
      3B-30 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
      Text in Illustration
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 *b

      Component without harness connected

      (Instrument Panel Junction Block Assembly)
      *c

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)


    1. Disconnect the L9*1 or M8*2 power window regulator motor assembly (for front passenger door) connector.


      • *1: for LHD

      • *2: for RHD

    2. Disconnect the M4*1 or L13*2 multiplex network master switch assembly connector.


      • *1: for LHD

      • *2: for RHD

    3. Disconnect the T4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

    4. Disconnect the N2 power window regulator motor assembly (for rear RH door) connector

    5. Disconnect the O2 power window regulator motor assembly (for rear LH door) connector.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      3C-26 (LIN2) - O2-9 (LIN) Always Below 1 Ω
      3B-30 (LIN2) - N2-9 (LIN) Always Below 1 Ω
      3B-30 (LIN2) - M4-17 (LIN1) Always Below 1 Ω
      3B-30 (LIN2) - L9-9 (LIN) Always Below 1 Ω
      3B-30 (LIN2) - T4-11 (MPX1) Always Below 1 Ω
      3C-26 (LIN2) - Body ground Always 10 kΩ or higher
      3B-30 (LIN2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      3C-26 (LIN2) - O2-9 (LIN) Always Below 1 Ω
      3B-30 (LIN2) - N2-9 (LIN) Always Below 1 Ω
      3B-30 (LIN2) - L13-17 (LIN1) Always Below 1 Ω
      3B-30 (LIN2) - M8-9 (LIN) Always Below 1 Ω
      3B-30 (LIN2) - T4-11 (MPX1) Always Below 1 Ω
      3C-26 (LIN2) - Body ground Always 10 kΩ or higher
      3B-30 (LIN2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR))


    1. Reconnect the M4*1 or L13*2 multiplex network master switch assembly connector.


      • *1: for LHD

      • *2: for RHD

    2. Reconnect the 3B and 3C instrument panel junction block assembly connector.

    3. Reconnect the T4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

    4. Reconnect the N2 power window regulator motor assembly (for rear RH door) connector.

    5. Reconnect the M8*1 or L9*2 power window regulator motor assembly (for driver door) connector.


      • *1: for LHD

      • *2: for RHD

    6. Reconnect the L9*1 or M8*2 power window regulator motor assembly (for front passenger door) connector.


      • *1: for LHD

      • *2: for RHD

    7. Clear the DTCs Click here.

    8. After 10 seconds have elapsed, check if the trouble occurs again.

    9. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) Click here

    A

  6. CHECK DTC OUTPUT (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)


    1. Reconnect the O2 power window regulator motor assembly (for rear LH door) connector.

    2. Disconnect the M4*1 or L13*2 multiplex network master switch assembly connector.


      • *1: for LHD

      • *2: for RHD

    3. Clear the DTCs Click here.

    4. After 10 seconds have elapsed, check if the trouble occurs again.

    5. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    A

  7. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR))


    1. Reconnect the M4*1 or L13*2 multiplex network master switch assembly connector.


      • *1: for LHD

      • *2: for RHD

    2. Disconnect the N2 power window regulator motor assembly (for rear RH door) connector.

    3. Clear the DTCs Click here.

    4. After 10 seconds have elapsed, check if the trouble occurs again.

    5. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) Click here

    A

  8. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR))


    1. Reconnect the N2 power window regulator motor assembly (for rear RH door) connector.

    2. Disconnect the M8*1 or L9*2 power window regulator motor assembly (for driver door) connector.


      • *1: for LHD

      • *2: for RHD

    3. Clear the DTCs Click here.

    4. After 10 seconds have elapsed, check if the trouble occurs again.

    5. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) Click here

    A

  9. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR))


    1. Reconnect the M8*1 or L9*2 power window regulator motor assembly (for driver door) connector.


      • *1: for LHD

      • *2: for RHD

    2. Disconnect the L9*1 or M8*2 power window regulator motor assembly (for front passenger door) connector.


      • *1: for LHD

      • *2: for RHD

    3. Clear the DTCs Click here.

    4. After 10 seconds have elapsed, check if the trouble occurs again.

    5. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) Click here

    A

  10. CHECK DTC OUTPUT (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY))


    1. Reconnect the L9*1 or M8*2 power window regulator motor assembly (for front passenger door) connector.


      • *1: for LHD

      • *2: for RHD

    2. Disconnect the T4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

    3. Clear the DTCs Click here.

    4. After 10 seconds have elapsed, check if the trouble occurs again.

    5. Check for DTCs again.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    B

    REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) Click here