BLIND SPOT MONITOR SYSTEM, Diagnostic DTC:C1AB5

DTC Code DTC Name
C1AB5 Open in Outer Mirror Indicator(Slave)

DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects an open in the outer rear view mirror indicator RH.

DTC No. DTC Detection Condition Trouble Area
C1AB5

    Both of the following conditions are met:

  • Blind spot monitor main switch (warning canceling switch assembly) is on.


  • The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator.

  • Outer rear view mirror RH (outer rear view mirror indicator RH)

  • Outer rear view mirror assembly RH

  • Wire harness or connector

  • Blind spot monitor sensor RH

  • Outer mirror control ECU assembly RH

WIRING DIAGRAM

A0007ZHE24

CAUTION / NOTICE / HINT

Note

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

PROCEDURE


  1. CHECK DTC


    1. Clear the DTCs Click here.

    2. Recheck for DTCs and check if the same DTC is output again.

      OK
      No DTCs are output.

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH, BODY GROUND - OUTER MIRROR CONTROL ECU ASSEMBLY RH)


    1. Disconnect the U9 blind spot monitor sensor RH connector.

    2. Disconnect the L10 outer mirror control ECU assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U9-4 (OMIR) - L10-13 (BDSR) Always Below 1 Ω
      L10-7 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH


    1. Disconnect the z11 outer mirror control ECU assembly RH connector.

    2. A0004MNE02
      Text in Illustration
      *a

      Component without harness connected

      (Outer Mirror Control ECU Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L10-13 (BDSR) - z11-8 (BSM) Always Below 1 Ω
      L10-7 (GND) - z11-12 (-) Always Below 1 Ω

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - OUTER REAR VIEW MIRROR RH)


    1. Disconnect the IND1 outer rear view mirror RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z11-8 (BSM) - IND1-1 (+) Always Below 1 Ω
      z11-12 (-) - IND1-2 (-) Always Below 1 Ω

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH Click here

    OK

  5. REPLACE OUTER REAR VIEW MIRROR RH


    1. Replace the outer rear view mirror RH Click here.


    NEXT

  6. CHECK DTC


    1. Clear the DTCs Click here.

    2. Recheck for DTCs and check if the same DTC is output again.

      OK
      No DTCs are output.

    OK

    END (OUTER REAR VIEW MIRROR RH WAS DEFECTIVE)

    NG

    REPLACE BLIND SPOT MONITOR SENSOR RH Click here