PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function) Guide Lines and Buttons are not Displayed for All Display Modes

DESCRIPTION

The multi-media module receiver assembly receives luggage compartment door open/close signals from the main body ECU (multiplex network body ECU) via CAN communication. When the luggage compartment door is open, the camera aiming cannot be adjusted correctly because the rear television camera assembly is installed on the luggage compartment door. Therefore, when performing back camera position setting while the luggage compartment door is open, a luggage compartment door open warning message will be displayed on the screen and back camera position setting will be canceled.

Tech Tips


  • Check the parking assist monitor screen display mode settings. (Check if the parking guide lines are set to off.)

WIRING DIAGRAM

A0007XXE06

CAUTION / NOTICE / HINT

Note


  • When "System initializing" is displayed on the multi-display assembly after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed Click here.

PROCEDURE


  1. CHECK LUGGAGE COMPARTMENT DOOR OPENER SYSTEM


    1. Check the luggage compartment door opener system Click here.

      OK
      Luggage compartment door opener system is normally.
      Result
      Result Proceed to
      OK A
      NG (w/o Power Trunk Lid System) B
      NG (w/ Power Trunk Lid System) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    GO TO LUGGAGE COMPARTMENT DOOR CLOSER SYSTEM Click here

    B

  2. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Luggage Courtesy SW Luggage courtesy switch signal/ON or OFF

      ON: Luggage compartment door open

      OFF: Luggage compartment door closed

      		 -
      OK
      The luggage compartment door courtesy switch functions as specified in the normal condition column.

    OK

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    NG

  3. INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY


    1. A0004OEE06
      Text in Illustration
      *a

      Component without harness connected

      (Luggage Compartment Door Lock Assembly)
      *b Close (Lock)
      *c Open (Unlock)

      Remove the luggage compartment door lock assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (D+) - 2 (E) Close (Lock) 10 kΩ or higher
      3 (D+) - 2 (E) Open (Unlock) Below 1 Ω

    NG

    REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    1. Disconnect the U3 luggage compartment door lock assembly connector.

    2. Disconnect the H10 main body ECU (multiplex network body ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U3-3 (D+) - H10-19 (LGCY) Always Below 1 Ω
      U3-2 (E) - Body ground Always Below 1 Ω
      U3-3 (D+) - Body ground Always 10 kΩ or higher

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR