Click here

NAVIGATION SYSTEM Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter

Click here
Click here
DTC Code DTC Name
  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter
Click here

DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

Tip:

  • A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

  • If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.

Click here

WIRING DIAGRAM

Click here

PROCEDURE


  1. Click here

    INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)


    1. A0008ZQE01

      Check the output waveform.


      1. Remove the combination meter assembly with the connector(s) still connected.

      2. Connect an oscilloscope to terminal H14-19 (+S) and body ground.

      3. Turn the power switch on (IG).

      4. Turn a wheel slowly.

      5. Check the signal waveform according to the condition(s) in the table below.

        Item Condition
        Measurement terminal H14-19 (+S) - Body ground
        Tool setting 5 V/DIV., 20 ms./DIV.
        Vehicle condition Wheel being rotated
        OK
        The waveform is similar to that shown in the illustration.
        Tip:

        When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

        Table 1. Text in Illustration
        *a

        Component with harness connected

        (Combination Meter Assembly)

  2. Click here

    INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)


    1. A00079RE01

      Check the input waveform.


      1. Remove the stereo component amplifier assembly with the connector(s) still connected.

      2. Connect an oscilloscope to terminal H99-17 (SPD) and body ground.

      3. Turn the power switch on (IG).

      4. Turn a wheel slowly.

      5. Check the signal waveform according to the condition(s) in the table below.

        Item Condition
        Measurement terminal H99-17 (SPD) - Body ground
        Tool setting 5 V/DIV., 20 ms./DIV.
        Vehicle condition Wheel being rotated
        OK
        The waveform is similar to that shown in the illustration.
        Tip:

        When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

        Table 2. Text in Illustration
        *a

        Component with harness connected

        (Stereo Component Amplifier Assembly)

  3. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the H115 junction connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-17 (SPD) - H115-21 Always Below 1 Ω

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. Click here

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)


    1. Disconnect the H14 combination meter assembly connector.

    2. Disconnect the H115 junction connector (for LHD).

      Disconnect the H114 junction connector (for RHD).

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 3. for LHD:
      Tester Connection Condition Specified Condition
      H14-19 (+S) - H115-20 Always Below 1 Ω
      Table 4. for RHD:
      Tester Connection Condition Specified Condition
      H14-19 (+S) - H114-12 Always Below 1 Ω

    • OK

      REPLACE JUNCTION CONNECTOR

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR