NAVIGATION SYSTEM Speaker Circuit

DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects the short and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, telematics transceiver* or speakers.


WIRING DIAGRAM

Figure 1. for 8 Speakers

A00047NE23

Figure 2. for 8 Speakers

A0003ERE34

Figure 3. for 15 Speakers

A0009MAE19

Figure 4. for 15 Speakers

A000778E19

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click here

PROCEDURE


  1. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 8 Speakers A
      for 15 Speakers B

    B

    CHECK SPEAKER (OPERATION CHECK) Click here

    A

  2. CHECK SPEAKER (OPERATION CHECK)


    1. A000997

      Enter the "System Check Mode" screen. Refer to Check SP Check On in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly A
      Front No. 1 speaker assembly B
      Front No. 3 speaker assembly C
      Rear speaker assembly D
      Stereo component speaker assembly E

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - STEREO COMPONENT SPEAKER ASSEMBLY) Click here

    A

  3. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      w/ Manual (SOS) Switch A
      w/o Manual (SOS) Switch B

    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) Click here

    A

  4. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the H101 telematics transceiver connector.

    3. Disconnect the H63 and H62 front No. 2 speaker assembly connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-13 (FR+) - H101-2 (SPI+) Always Below 1 Ω
      H99-28 (FR-) - H101-3 (SPI-) Always Below 1 Ω
      H101-5 (SPO+) - H63-2 Always Below 1 Ω
      H101-6 (SPO-) - H63-1 Always Below 1 Ω
      H99-12 (FL+) - H62-2 Always Below 1 Ω
      H99-27 (FL-) - H62-1 Always Below 1 Ω
      H99-13 (FR+) or H101-2 (SPI+) - Body ground Always 10 kΩ or higher
      H99-28 (FR-) or H101-3 (SPI-) - Body ground Always 10 kΩ or higher
      H99-12 (FL+) or H62-2 - Body ground Always 10 kΩ or higher
      H99-27 (FL-) or H62-1 - Body ground Always 10 kΩ or higher
      H101-5 (SPO+) or H63-2 - Body ground Always 10 kΩ or higher
      H101-6 (SPO-) or H63-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. A0007JDC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 7 Click here

    NG

    REPLACE DCM (TELEMATICS TRANSCEIVER) Click here

  6. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the H63 and H62 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-13 (FR+) - H63-2 Always Below 1 Ω
      H99-28 (FR-) - H63-1 Always Below 1 Ω
      H99-12 (FL+) - H62-2 Always Below 1 Ω
      H99-27 (FL-) - H62-1 Always Below 1 Ω
      H99-13 (FR+) or H63-2 - Body ground Always 10 kΩ or higher
      H99-28 (FR-) or H63-1 - Body ground Always 10 kΩ or higher
      H99-12 (FL+) or H62-2 - Body ground Always 10 kΩ or higher
      H99-27 (FL-) or H62-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

  8. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the L6 and M5 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-5 (WFR+) - L6-1 Always Below 1 Ω
      H99-20 (WFR-) - L6-2 Always Below 1 Ω
      H99-4 (WFL+) - M5-1 Always Below 1 Ω
      H99-19 (WFL-) - M5-2 Always Below 1 Ω
      H99-5 (WFR+) or L6-1 - Body ground Always 10 kΩ or higher
      H99-20 (WFR-) or L6-2 - Body ground Always 10 kΩ or higher
      H99-4 (WFL+) or M5-1 - Body ground Always 10 kΩ or higher
      H99-19 (WFL-) M5-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  10. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the J2 front No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-7 (CTR+) - J2-2 Always Below 1 Ω
      H99-22 (CTR-) - J2-1 Always Below 1 Ω
      H99-7 (CTR+) or J2-2 - Body ground Always 10 kΩ or higher
      H99-22 (CTR-) or J2-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

  12. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the N6 and O6 rear speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-15 (RR+) - N6-1 Always Below 1 Ω
      H99-30 (RR-) - N6-2 Always Below 1 Ω
      H99-14 (RL+) - O6-1 Always Below 1 Ω
      H99-29 (RL-) - O6-2 Always Below 1 Ω
      H99-15 (RR+) or N6-1- Body ground Always 10 kΩ or higher
      H99-30 (RR-) or N6-2 - Body ground Always 10 kΩ or higher
      H99-14 (RL+) or O6-1 - Body ground Always 10 kΩ or higher
      H99-29 (RL-) or O6-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

  14. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - STEREO COMPONENT SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the Q16 stereo component speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-6 (WF1+) - Q16-1 Always Below 1 Ω
      H99-21 (WF1-) - Q16-2 Always Below 1 Ω
      H99-6 (WF1+) or Q16-1 - Body ground Always 10 kΩ or higher
      H99-21 (WF1-) or Q16-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  15. INSPECT STEREO COMPONENT SPEAKER ASSEMBLY


    1. Remove the stereo component speaker assembly.

      Click here

    2. Inspect the stereo component speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE STEREO COMPONENT SPEAKER ASSEMBLY Click here

  16. CHECK SPEAKER (OPERATION CHECK)


    1. A000997

      Enter the "System Check Mode" screen. Refer to Check SP Check On in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly A
      Front No. 1 speaker assembly B
      Front No. 3 speaker assembly C
      Rear speaker assembly or rear No. 2 speaker assembly D
      Rear header speaker assembly E
      Stereo component speaker assembly F

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - STEREO COMPONENT SPEAKER ASSEMBLY) Click here

    A

  17. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      w/ Manual (SOS) Switch A
      w/o Manual (SOS) Switch B

    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) Click here

    A

  18. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the H101 telematics transceiver connector.

    3. Disconnect the H63 and H62 front No. 2 speaker assembly connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-13 (FR+) - H101-2 (SPI+) Always Below 1 Ω
      H99-28 (FR-) - H101-3 (SPI-) Always Below 1 Ω
      H101-5 (SPO+) - H63-2 Always Below 1 Ω
      H101-6 (SPO-) - H63-1 Always Below 1 Ω
      H99-12 (FL+) - H62-2 Always Below 1 Ω
      H99-27 (FL-) - H62-1 Always Below 1 Ω
      H99-13 (FR+) or H101-2 (SPI+) - Body ground Always 10 kΩ or higher
      H99-28 (FR-) or H101-3 (SPI-) - Body ground Always 10 kΩ or higher
      H99-12 (FL+) or H62-2 - Body ground Always 10 kΩ or higher
      H99-27 (FL-) or H62-1 - Body ground Always 10 kΩ or higher
      H101-5 (SPO+) or H63-2 - Body ground Always 10 kΩ or higher
      H101-6 (SPO-) or H63-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  19. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. A0007JDC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 21 Click here

    NG

    REPLACE DCM (TELEMATICS TRANSCEIVER) Click here

  20. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the H63 and H62 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-13 (FR+) - H63-2 Always Below 1 Ω
      H99-28 (FR-) - H63-1 Always Below 1 Ω
      H99-12 (FL+) - H62-2 Always Below 1 Ω
      H99-27 (FL-) - H62-1 Always Below 1 Ω
      H99-13 (FR+) or H63-2 - Body ground Always 10 kΩ or higher
      H99-28 (FR-) or H63-1 - Body ground Always 10 kΩ or higher
      H99-12 (FL+) or H62-2 - Body ground Always 10 kΩ or higher
      H99-27 (FL-) or H62-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  21. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

    3. Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  22. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the L6 and M5 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-5 (WFR+) - L6-1 Always Below 1 Ω
      H99-20 (WFR-) - L6-2 Always Below 1 Ω
      H99-4 (WFL+) - M5-1 Always Below 1 Ω
      H99-19 (WFL-) - M5-2 Always Below 1 Ω
      H99-5 (WFR+) or L6-1 - Body ground Always 10 kΩ or higher
      H99-20 (WFR-) or L6-2 - Body ground Always 10 kΩ or higher
      H99-4 (WFL+) or M5-1 - Body ground Always 10 kΩ or higher
      H99-19 (WFL-) or M5-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  23. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  24. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the J2 front No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-7 (CTR+) - J2-2 Always Below 1 Ω
      H99-22 (CTR-) - J2-1 Always Below 1 Ω
      H99-7 (CTR+) or J2-2 - Body ground Always 10 kΩ or higher
      H99-22 (CTR-) or J2-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  25. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

    3. Check that the malfunction disappears when a new or known good front No. 3 speaker assembly is installed.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  26. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the N7 and O7 rear No. 2 speaker assembly connectors.

    3. Disconnect the N6 and O6 rear speaker assembly connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-15 (RR+) - N7-3 (+TW) Always Below 1 Ω
      H99-30 (RR-) - N7-1 (-TW) Always Below 1 Ω
      H99-14 (RL+) - O7-3 (+TW) Always Below 1 Ω
      H99-29 (RL-) - O7-1 (-TW) Always Below 1 Ω
      N6-1 - N7-4 (+) Always Below 1 Ω
      N6-2 - N7-2 (-) Always Below 1 Ω
      O6-1 - O7-4 (+) Always Below 1 Ω
      O6-2 - O7-2 (-) Always Below 1 Ω
      H99-15 (RR+) or N7-3 (+TW) - Body ground Always 10 kΩ or higher
      H99-30 (RR-) or N7-1 (-TW) - Body ground Always 10 kΩ or higher
      H99-14 (RL+) or O7-3 (+TW) - Body ground Always 10 kΩ or higher
      H99-29 (RL-) or O7-1 (-TW) - Body ground Always 10 kΩ or higher
      N6-1 or N7-4 (+) - Body ground Always 10 kΩ or higher
      N6-2 or N7-2 (-) - Body ground Always 10 kΩ or higher
      O6-1 or O7-4 (+) - Body ground Always 10 kΩ or higher
      O6-2 or O7-2 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  27. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  28. INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. Inspect the rear No. 2 speaker assembly.

      Click here

    3. Check that the malfunction disappears when a new or known good rear No. 2 speaker assembly is installed.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  29. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the Q15 and P32 rear header speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-11 (SR+) - Q15-2 Always Below 1 Ω
      H99-26 (SR-) - Q15-1 Always Below 1 Ω
      H99-10 (SL+) - P32-2 Always Below 1 Ω
      H99-25 (SL-) - P32-1 Always Below 1 Ω
      H99-11 (SR+) or Q15-2 - Body ground Always 10 kΩ or higher
      H99-26 (SR-) or Q15-1 - Body ground Always 10 kΩ or higher
      H99-10 (SL+) or P32-2 - Body ground Always 10 kΩ or higher
      H99-25 (SL-) or P32-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  30. INSPECT REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. Inspect the rear header speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR HEADER SPEAKER ASSEMBLY Click here

  31. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - STEREO COMPONENT SPEAKER ASSEMBLY)


    1. Disconnect the H99 stereo component amplifier assembly connector.

    2. Disconnect the Q16 stereo component speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H99-6 (WF1+) - Q16-1 Always Below 1 Ω
      H99-21 (WF1-) - Q16-2 Always Below 1 Ω
      H99-6 (WF1+) or Q16-1 - Body ground Always 10 kΩ or higher
      H99-21 (WF1-) or Q16-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  32. INSPECT STEREO COMPONENT SPEAKER ASSEMBLY


    1. Remove the stereo component speaker assembly.

      Click here

    2. Inspect the stereo component speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE STEREO COMPONENT SPEAKER ASSEMBLY Click here