Click here

NAVIGATION SYSTEM, Diagnostic DTC:B15DA

Click here
Click here
DTC Code DTC Name
B15DA Rear Console Recognition Disconnected
Click here

DESCRIPTION

The multi-display assembly and cooler control switch assembly are connected by the AVC-LAN communication line.

The multi-media module receiver assembly is also connected to the multi-display assembly by the AVC-LAN communication line.

When an AVC-LAN communication error occurs between the multi-display assembly and cooler control switch assembly, this DTC will be stored.

Tip:

If B15DA and B15D6 are output, troubleshoot for B15D6 first.

DTC No. DTC Detection Condition Trouble Area
B15DA

When either condition below is met:


  • Cooler control switch assembly is/was not connected while the power switch is/was on (IG or ACC).

  • Communication between the master unit and the cooler control switch assembly is/was not possible when the hybrid system is started.

  • Cooler control switch assembly power source circuit

  • AVC-LAN circuit between navigation receiver assembly and cooler control switch assembly

  • Cooler control switch assembly

  • Multi-display assembly

  • Multi-media module receiver assembly

  • Harness or connector
Tip:

  • Even if no fault is present, this DTC may be stored depending on the auxiliary battery condition or hybrid system start voltage.

  • The multi-media module receiver assembly is the master unit.

Click here

WIRING DIAGRAM


Click here
  1. A0007CTE14
Click here

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precautions for Navigation System (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK DTC


    1. Clear the DTCs (Click here).

    2. Recheck for DTCs and check if the same DTC is output again.

      Result
      Result Proceed to
      B15DA is output. A
      B15DA and B15D6 are output. B
      No DTCs are output. C
      Tip:

      If B15DA and B15D6 are output, troubleshoot for B15D6 first.


  2. Click here

    CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check for optional components


      1. Check that optional components (including associated wiring) which generate radio waves are not installed.

        Result
        Result Proceed to
        Optional components (including associated wiring) are installed. A
        Optional components (including associated wiring) are not installed. B
      Tip:

      • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

      • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.


  3. Click here

    REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note:

      Do not remove optional components or associated wiring without the permission of the customer.


  4. Click here

    CHECK DTC


    1. Clear the DTCs (Click here).

    2. Recheck for DTCs and check if the same DTC is output again.

      OK
      No DTCs are output.

  5. Click here

    CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY POWER SOURCE)


    1. Disconnect the j2 cooler control switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      j2-16 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      j2-1 (+B) - j2-16 (GND) Power switch off 11 to 14 V
      j2-7 (IG+) - j2-16 (GND) Power switch on (IG) 11 to 14 V
      j2-6 (ACC) - j2-16 (GND) Power switch on (ACC) 11 to 14 V

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - COOLER CONTROL SWITCH ASSEMBLY)


    1. Disconnect the H93 multi-display assembly connector.

    2. Disconnect the j2 cooler control switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H93-6 (TX1+) - j2-15 (TX+) Always Below 1 Ω
      H93-18 (TX1-) - j2-5 (TX-) Always Below 1 Ω
      H93-6 (TX1+) - Body ground Always 10 kΩ or higher
      H93-18 (TX1-) - Body ground Always 10 kΩ or higher

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. Click here

    REPLACE COOLER CONTROL SWITCH ASSEMBLY


    1. Replace the cooler control switch assembly (Click here).

    2. Clear the DTCs (Click here).

    3. Recheck for DTCs and check if the same DTC is output again.

      OK
      No DTCs are output.

  8. Click here

    REPLACE MULTI-DISPLAY ASSEMBLY


    1. Replace the multi-display assembly (Click here).

    2. Clear the DTCs (Click here).

    3. Recheck for DTCs and check if the same DTC is output again.

      OK
      No DTCs are output.

    • OK

      END

    • NG

      REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)