NAVIGATION SYSTEM, Diagnostic DTC:B15C2

DTC Code DTC Name
B15C2 Speed Signal Malfunction

DESCRIPTION

The multi-media module receiver assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The multi-media module receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

Tech Tips


  • A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

  • If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.

DTC No. DTC Detection Condition Trouble Area
B15C2 A difference between the GPS speed and SPD pulse is detected.

  • Multi-media module receiver assembly

  • Combination meter assembly

  • Harness or connector

  • Junction block

WIRING DIAGRAM

A0003JCE02

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precautions for Navigation System Click here.

PROCEDURE


  1. CHECK VEHICLE SENSOR (OPERATION CHECK)


    1. A00054N

      Enter the "Vehicle Sensors" screen. Refer to Check GPS & Vehicle Sensors in Operation Check Click here.

    2. While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.

      Tech Tips

      The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

      OK
      Vehicle speed displayed on the "Vehicle Sensors" screen is almost the same as the actual vehicle speed measured using the GTS (See page Click here).

    OK

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    NG

  2. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)


    1. A0009I9E02
      Text in Illustration
      *a

      Component with harness connected

      (Combination Meter Assembly)

      Check the output waveform.


      1. Remove the combination meter assembly with the connector still connected.

      2. Connect an oscilloscope to terminal H14-19 (+S) and body ground.

      3. Turn the power switch on (IG).

      4. Turn a wheel slowly.

      5. Check the signal waveform according to the condition(s) in the table below.

        Item Condition
        Measurement terminal H14-19 (+S) - Body ground
        Tool setting 5 V/DIV., 20 ms./DIV.
        Vehicle condition Wheel being rotated
        OK
        The waveform is similar to that shown in the illustration.

        Tech Tips

        When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


    NG

    GO TO METER / GAUGE SYSTEM Click here

    OK

  3. INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY (INPUT WAVEFORM)


    1. A00067DE01
      Text in Illustration
      *a

      Component with harness connected

      (Multi-media Module Receiver Assembly)

      Check the input waveform.


      1. Remove the multi-media module receiver assembly with the connector still connected.

      2. Connect an oscilloscope to terminal H97-56 (SPD) and body ground.

      3. Turn the power switch on (IG).

      4. Turn a wheel slowly.

      5. Check the signal waveform according to the condition(s) in the table below.

        Item Condition
        Measurement terminal H97-56 (SPD) - Body ground
        Tool setting 5 V/DIV., 20 ms./DIV.
        Vehicle condition Wheel being rotated
        OK
        The waveform is similar to that shown in the illustration.

        Tech Tips

        When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


    OK

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    NG

  4. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - JUNCTION CONNECTOR)


    1. Disconnect the H97 multi-media module receiver assembly connector.

    2. Disconnect the H114 junction connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-56 (SPD) - H114-15 Always Below 1 Ω

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION BLOCK)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - JUNCTION CONNECTOR)