NAVIGATION SYSTEM, Diagnostic DTC:B15C0, B15C1

DTC Code DTC Name
B15C0 GPS Antenna Connection Malfunction(short)
B15C1 GPS Antenna Connection Malfunction(break)

DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Connection Malfunction(short) Navigation antenna assembly error

  • Navigation antenna assembly*1

  • Antenna cord sub-assembly*2

  • No. 2 antenna cord sub-assembly*2

  • No. 3 antenna cord sub-assembly*2

  • Telephone antenna assembly*2

  • Radio receiver assembly
B15C1 GPS Antenna Connection Malfunction(break) Navigation antenna assembly power source malfunction

  • Navigation antenna assembly*1

  • Antenna cord sub-assembly*2

  • No. 2 antenna cord sub-assembly*2

  • No. 3 antenna cord sub-assembly*2

  • Telephone antenna assembly*2

  • Radio receiver assembly

CAUTION / NOTICE / HINT

Note


  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here

  • Check that the navigation antenna assembly cable is properly installed and does not have any sharp bends, pinching or loose connections before performing the following inspection procedure.

    Click here

PROCEDURE


  1. CHECK DTC


    1. Clear the DTCs.

      Click here

    2. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Model Proceed to
      w/o Blocking System A
      w/ Blocking System B

    B

    REPLACE ANTENNA CORD SUB-ASSEMBLY Click here

    A

  3. INSPECT NAVIGATION ANTENNA ASSEMBLY


    1. Remove the navigation antenna assembly.

      Click here

    2. A01W00IC18
      *a

      Component without harness connected

      (Navigation Antenna Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 1a Always 50 to 500 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

    REPLACE NAVIGATION ANTENNA ASSEMBLY Click here

  4. REPLACE ANTENNA CORD SUB-ASSEMBLY


    1. Replace the antenna cord sub-assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here

    3. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  5. REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. Replace the No. 2 antenna cord sub-assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here

    3. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  6. REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. Replace the No. 3 antenna cord sub-assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here

    3. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  7. REPLACE TELEPHONE ANTENNA ASSEMBLY


    1. Replace the telephone antenna assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here

    3. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here