NAVIGATION SYSTEM, Diagnostic DTC:B1321, B1323, B1563

DTC Code DTC Name
B1321 Lost Communication with EMV
B1323 Lost Communication with Haptic Device
B1563 Haptic Device Disconnected

DESCRIPTION

These DTCs are stored when communication between the multi-media module receiver assembly and remote touch is not possible.

DTC No. DTC Detection Condition Trouble Area
B1321 The multi-media module receiver assembly cannot receive data from the remote touch.

  • Local bus circuit between multi-media module receiver assembly and remote touch (remote operation board)

  • Remote touch (remote operation board) power source circuit

  • Remote touch (remote operation board)

  • Multi-media module receiver assembly
B1323 The remote touch cannot receive data from the multi-media module receiver assembly.
B1563 The remote touch is not/was not connected while the power switch is/was on (ACC or IG).

WIRING DIAGRAM

A0003J9E10

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precautions for Navigation System Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - REMOTE TOUCH (REMOTE OPERATION BOARD) )


    1. Disconnect the H97 multi-media module receiver assembly connector.

    2. Disconnect the H95 remote touch (remote operation board) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-3 (CNH1) - H95-5 (MO+) Always Below 1 Ω
      H97-4 (CNL1) - H95-4 (MO-) Always Below 1 Ω
      H97-3 (CNH1) - Body ground Always Below 1 Ω
      H97-4 (CNL1) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION BOARD) POWER SOURCE)


    1. Disconnect the H95 remote touch (remote operation board) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H95-1 (+B) - Body ground Power switch off 11 to 14 V
      H95-2 (ACC) - Body ground Power switch on (ACC) 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H95-15 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. REMOTE TOUCH SELF CHECK (REMOTE TOUCH SWITCH KNOB FEEDBACK FORCE GENERATION CHECK)


    1. A0004V0E01
      Text in Illustration
      *a Switch Knob
      *b Control Direction
      *c Feedback Force

      Check the remote touch switch knob feedback force.


      1. Move the remote touch switch knob up, down, right and left to check that feedback force is generated.

        OK
        Feedback force is generated.

        Tech Tips

        When the power switch is turned on (ACC), feedback force is generated. When the power switch is turned off, feedback force is not generated, and the remote touch switch knob will move freely.


    NG

    REPLACE REMOTE OPERATION BOARD Click here

    OK

  4. REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY


    1. Replace the multi-media module receiver assembly Click here.

    2. Check if the same malfunction recurs.

      Result
      Result Proceed to

      Malfunction does not recur

      (returns to normal)

      		 A
      Malfunction recurs B

    A

    END

    B

    REPLACE REMOTE OPERATION BOARD Click here