RADIO ANTENNA CORD INSTALLATION

Info Added 2017-08-02

PROCEDURE


  1. INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (for LH Side with Digital Audio Broadcasting Antenna)


    1. Engage the 4 clamps.

    2. Install the No. 4 antenna cord sub-assembly with the bolt.

    3. Connect the 2 connectors.

  2. INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (for RH Side with Digital Audio Broadcasting Antenna)


    1. Engage the 5 clamps to install the No. 4 antenna cord sub-assembly.

    2. Connect the connector.

  3. INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY (w/ Roof Antenna)


    1. Engage the 4 clamps to install the No. 3 antenna cord sub-assembly.

    2. Connect the connector.

  4. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. Apply double-sided tape as shown in the illustration.

      A0007HFE03
      Text in Illustration
      *1 Marking - -
      *a Double-sided Tape Size *b Tape Attachment Locations (Reference)
      A0007SL Double-sided Tape - -
      A0009JS Front - -
      Double-sided Tape Size
      Area Dimension
      X 1.0 mm (0.0394 in.)
      Y 10.0 mm (0.394 in.)

    2. Peel off the release paper from the double-sided tape.

    3. Align the marking tape on the No. 2 antenna cord sub-assembly with the vehicle front end on the roof headlining assembly. (A)

      A0006VOE03
      Text in Illustration
      *1 Adjustment Area - -
      A0007U0 Marking Tape A0007SL Adhesive Tape
      A0009JS Front - -

    4. Engage the 2 guides. (B)

    5. Align the marking tape on the No. 2 antenna cord sub-assembly with the vehicle rear end on the roof headlining assembly. (C)

    6. Align the marking tape on the No. 2 antenna cord sub-assembly with the adjustment area on the roof headlining assembly. (D)

    7. Attach the No. 2 antenna cord sub-assembly with the double-sided tape.

      Note


      • Securely attach the No. 2 antenna cord sub-assembly.

      • If any of the No. 2 antenna cord sub-assembly is left loose, this will cause abnormal noise.

      • Make sure to attach the No. 2 antenna cord sub-assembly without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.

    8. Apply adhesive tape by aligning it with the markings on the roof headlining as shown in the illustration.

  5. INSTALL ROOF HEADLINING ASSEMBLY

    Click here

  6. INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)


    1. w/o Navigation System:


      1. Engage the 6 clamps to install the antenna cord sub-assembly.

    2. w/ Navigation System:


      1. Engage the 7 clamps to install the antenna cord sub-assembly.

  7. INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)


    1. Engage the 7 clamps to install the antenna cord sub-assembly.

  8. INSTALL NO. 3 HEATER TO REGISTER DUCT

    Click here

  9. INSTALL DEFROSTER NOZZLE ASSEMBLY

    Click here

  10. INSTALL NO. 1 DEFROSTER NOZZLE GARNISH

    Click here

  11. INSTALL AUTOMATIC LIGHT CONTROL SENSOR

    Click here

  12. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT

    Click here

  13. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT

    Click here

  14. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

    Click here