Click here

RADIO ANTENNA CORD INSTALLATION

Click here

Info Added 2017-08-02

Click here

PROCEDURE


  1. Click here

    INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (for LH Side with Digital Audio Broadcasting Antenna)


    1. Engage the 4 clamps.

    2. Install the No. 4 antenna cord sub-assembly with the bolt.

    3. Connect the 2 connectors.

  2. Click here

    INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (for RH Side with Digital Audio Broadcasting Antenna)


    1. Engage the 5 clamps to install the No. 4 antenna cord sub-assembly.

    2. Connect the connector.

  3. Click here

    INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY (w/ Roof Antenna)


    1. Engage the 4 clamps to install the No. 3 antenna cord sub-assembly.

    2. Connect the connector.

  4. Click here

    INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. A0007HFE03

      Apply double-sided tape as shown in the illustration.

      Table 1. Text in Illustration
      *1 Marking - -
      *a Double-sided Tape Size *b Tape Attachment Locations (Reference)
      A0007SL Double-sided Tape - -
      A0009JS Front - -
      Table 2. Double-sided Tape Size
      Area Dimension
      X 1.0 mm (0.0394 in.)
      Y 10.0 mm (0.394 in.)

    2. Peel off the release paper from the double-sided tape.

    3. A0006VOE03

      Align the marking tape on the No. 2 antenna cord sub-assembly with the vehicle front end on the roof headlining assembly. (A)

      Table 3. Text in Illustration
      *1 Adjustment Area - -
      A0007U0 Marking Tape A0007SL Adhesive Tape
      A0009JS Front - -

    4. Engage the 2 guides. (B)

    5. Align the marking tape on the No. 2 antenna cord sub-assembly with the vehicle rear end on the roof headlining assembly. (C)

    6. Align the marking tape on the No. 2 antenna cord sub-assembly with the adjustment area on the roof headlining assembly. (D)

    7. Attach the No. 2 antenna cord sub-assembly with the double-sided tape.

      Note:

      • Securely attach the No. 2 antenna cord sub-assembly.

      • If any of the No. 2 antenna cord sub-assembly is left loose, this will cause abnormal noise.

      • Make sure to attach the No. 2 antenna cord sub-assembly without leaving any of it loose.

      Tip:

      Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.

    8. Apply adhesive tape by aligning it with the markings on the roof headlining as shown in the illustration.

  5. Click here

    INSTALL ROOF HEADLINING ASSEMBLY

    (Click here)

  6. Click here

    INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)


    1. w/o Navigation System:


      1. Engage the 6 clamps to install the antenna cord sub-assembly.

    2. w/ Navigation System:


      1. Engage the 7 clamps to install the antenna cord sub-assembly.

  7. Click here

    INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)


    1. Engage the 7 clamps to install the antenna cord sub-assembly.

  8. Click here

    INSTALL NO. 3 HEATER TO REGISTER DUCT

    Click here

  9. Click here

    INSTALL DEFROSTER NOZZLE ASSEMBLY

    Click here

  10. Click here

    INSTALL NO. 1 DEFROSTER NOZZLE GARNISH

    Click here

  11. Click here

    INSTALL AUTOMATIC LIGHT CONTROL SENSOR

    Click here

  12. Click here

    INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT

    Click here

  13. Click here

    INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT

    Click here

  14. Click here

    INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

    (Click here)