Click here

AUDIO AND VISUAL SYSTEM(w/o Multi-display), Diagnostic DTC:01-DF

Click here
Click here
DTC Code DTC Name
01-DF Master Error
Click here

DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
01-DF*1

Either condition is met:


  • The device with a display fails and the master unit is switched to the audio device.

  • A communication error between the sub-master unit (audio) and master unit occurs.

  • Radio receiver assembly power source circuit

  • AVC-LAN circuit between the radio receiver assembly and component which has stored this code

  • Radio receiver assembly

  • Component which has stored this code
Tip:

*1: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the power switch on (IG) or (ACC), this DTC is stored.

Note:

  • Before starting troubleshooting, be sure to clear the DTCs stored due to the reason described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.

  • The radio receiver assembly is the master unit.

  • Be sure to clear and recheck for DTCs after the inspection is completed to confirm that no DTCs are output.

Click here

CAUTION / NOTICE / HINT

Note:

Be sure to read Description before performing the following procedure.

Click here

PROCEDURE


  1. Click here

    CHECK RADIO RECEIVER POWER SOURCE CIRCUIT


    1. Refer to Radio Receiver Power Source Circuit (Click here).

      Tip:

      If the power source circuit is operating normally, proceed to the next step.


  2. Click here

    INSPECT RADIO RECEIVER ASSEMBLY


    1. Disconnect the H82, H85 and H83 radio receiver assembly connectors.

    2. A0009R3E07
      A0006JME07

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H82-5 (ATX+) - H82-15 (ATX-) Always 60 to 80 Ω
      H85-9 (TXM+) - H85-10 (TXM-) Always 60 to 80 Ω
      H83-9 (TX+) - H83-10 (TX-) Always 60 to 80 Ω
      Table 1. Text in Illustration
      *a

      Component without harness connected

      (Radio Receiver Assembly)

  3. Click here

    IDENTIFY COMPONENT WHICH HAS STORED THIS CODE


    1. A00052VE22

      Enter diagnostic mode (Click here).

    2. Press preset switch "2" to change the mode to "Detailed Information Mode".

    3. Identify the component which has stored this code.

      Table 2. Component Table
      Component Physical Address
      Stereo component amplifier assembly 440
      Radio receiver assembly 190
      Accessory meter assembly 1D4
      Air conditioning control panel 1C4
      Tip:

      • The physical address "P440" shown in the above example indicates the stereo component amplifier assembly.

      • For details of the DTC display, refer to DTC Check/Clear (Click here).


  4. Click here

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMPONENT WHICH HAS STORED THIS CODE)

    Tip:

    For details of the connectors, refer to Terminals of ECU (Click here).


    1. Referring to the following AVC-LAN wiring diagram, check the AVC-LAN circuit between the radio receiver assembly and component which has stored this code.


      1. Disconnect all connectors between the radio receiver assembly and component which has stored this code.

      2. A0007G4E09

        Check for an open or short in the AVC-LAN circuit between the radio receiver assembly and component which has stored this code.

        OK
        There is no open or short circuit.

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. Click here

    REPLACE RADIO RECEIVER ASSEMBLY


    1. Replace the radio receiver assembly with a known good one (Click here).


  6. Click here

    CLEAR DTC


    1. Clear the DTCs (Click here).


  7. Click here

    RECHECK FOR DTC


    1. Recheck for DTCs and check that no DTCs are output (Click here).

      OK
      No DTCs are output.

    • OK

      END

    • NG

      REPLACE COMPONENT WHICH HAS STORED THIS CODE