AUDIO AND VISUAL SYSTEM(w/o Multi-display) Illumination Circuit

DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

A0009EYE10

CAUTION / NOTICE / HINT

Note


  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK ILLUMINATION


    1. Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

      Result
      Result Proceed to
      Illumination comes on for all components except steering pad switch assembly. A
      Illumination comes on for all components except radio receiver assembly. B
      No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). C
      Illumination comes on only for steering pad switch assembly. D

    B

    CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL) Click here

    C

    GO TO LIGHTING SYSTEM Click here

    D

    GO TO METER / GAUGE SYSTEM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)


    1. Disconnect the H22 spiral cable with sensor sub-assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H22-13 (IL+2) - Body ground Power switch off, light control switch in the tail or head position 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Disconnect the z5 steering pad switch assembly connector.

    2. Connect an auxiliary battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

      A0009AGE02

    3. Check if the illumination for the steering pad switch assembly comes on.

      OK
      Illumination for the steering pad switch assembly comes on.
      Text in Illustration
      *a

      Front view of wire harness connected

      (Steering Pad Switch Assembly)

      		 - -

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  4. INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Disconnect the z5 steering pad switch assembly connector.

    2. Disconnect the H22 spiral cable with sensor sub-assembly connector.

    3. A0005FKE02
      Text in Illustration
      *a

      Component without harness connected

      (Spiral Cable with Sensor Sub-assembly)
      *b Steering Pad Switch Assembly Side
      *c Vehicle Side

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z5-5 (IL+2) - H22-13 (IL+2) Center 3 Ω or less
      2.5 rotations to the left
      2.5 rotations to the right
      z5-3 (-DP) - H22-11 (-DP) Center 3 Ω or less
      2.5 rotations to the left
      2.5 rotations to the right

    4. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z5-5 (IL+2) - H22-13 (IL+2) Always 3 Ω or less
      z5-3 (-DP) - H22-11 (-DP) Always 3 Ω or less

      Note


      • The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

      • As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.

      Tech Tips



    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)

    NG

    REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY Click here

  5. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)


    1. Disconnect the H82 radio receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H82-2 (ILL+) - Body ground Power switch off, light control switch in the tail or head position 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)


    1. Disconnect the H82 radio receiver assembly connector.

    2. Disconnect the H14 combination meter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H82-12 (ILL-) - H14-39 (ILL-) Always Below 1 Ω
      H14-39 (ILL-) - Body ground Always 10 kΩ or higher

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR