STEERING COLUMN ASSEMBLY INSTALLATION

PROCEDURE


  1. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A0009BUE05
      Text in Illustration
      *a Matchmark

      Install the steering intermediate shaft assembly to the steering column assembly.

      Note

      Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.

    2. Install a new bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

  2. INSTALL STEERING POST ASSEMBLY


    1. Install the steering post assembly with the 4 nuts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

    2. Install the ground wire with the bolt.

      Torque:
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf }

    3. Engage the clamp.

    4. Connect the 2 connectors.

    5. Connect the connectors and engage the wire harness clamps to the steering post assembly.

  3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY


    1. Engage the 2 claws and guide to install the No. 2 air duct sub-assembly.

  4. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A0007AKE06
      Text in Illustration
      *a Matchmark

      Connect the steering intermediate shaft assembly to the steering link assembly.

      Note

      Align the matchmarks on the steering intermediate shaft assembly and the steering link assembly.

    2. Install a new bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }
    3. A0006HY

      Tighten the clamp.

  5. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the auxiliary battery connected and the power switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering post assembly.

    2. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

  6. INSTALL UPPER STEERING COLUMN COVER


    1. Engage the 2 claws to install the upper steering column cover.

    2. Engage the 4 clips and 2 guides to the upper steering column cover.

  7. INSTALL LOWER STEERING COLUMN COVER


    1. A0005HQ

      Engage the 2 claws to install the lower steering column cover.

    2. A0003YL

      Install the 3 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

  8. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  9. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

  10. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Click here

  11. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  12. INSPECT STEERING WHEEL CENTER POINT

  13. INSTALL HORN BUTTON ASSEMBLY

    Click here

  14. INSTALL FRONT WHEEL LH

    Torque:
    103 N*m  { 1049 kgf*cm, 76 ft.*lbf }

  15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note


    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    • Connect the cable to the negative (-) auxiliary battery terminal with the front wheels facing straight ahead Click here.

    • Reset the auto tilt away function setting to the previous condition by changing the customize parameter Click here.

  16. TORQUE SENSOR ZERO POINT CALIBRATION

    Click here

  17. ADJUST PARKING ASSIST MONITOR SYSTEM (w/ Parking Assist Monitor System)

    Click here