PARKING BRAKE ASSEMBLY REASSEMBLY

Info Added 2017-08-02

PROCEDURE


  1. APPLY HIGH TEMPERATURE GREASE


    1. A0005EP

      Apply high temperature grease to the areas of the parking brake plate which make contact with the shoe as shown in the illustration.

      Text in Illustration
      A0007SL High Temperature Grease

  2. INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN


    1. Install the 2 parking brake shoe hold down spring pins.

  3. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)


    1. Install the parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.

  4. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. Install the No. 1 parking brake shoe assembly to the parking brake shoe return tension spring.

  5. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A000707

      Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.

      Text in Illustration
      A0007SL High Temperature Grease

    2. Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.

  6. INSTALL PARKING BRAKE SHOE LEVER


    1. A000455

      Using needle-nose pliers, install the parking brake shoe lever to the No. 3 parking brake cable assembly.

    2. A0006PG

      Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.

      Text in Illustration
      A0007SL High Temperature Grease
    3. A0003RW

      Install the parking brake shoe lever to the No. 2 parking brake shoe assembly.

    4. Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and fit them to the parking brake plate.

      Note

      Make sure that the parking brake shoe lever does not separate from the No. 2 parking brake shoe assembly.

  7. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Rear Side)


    1. A0008EYE04

      Using SST, install the parking brake shoe hold down compression spring.

      SST
      09718-00011

  8. INSTALL PARKING BRAKE SHOE STRUT


    1. Install the parking brake shoe strut.

    2. A0009AE

      Install the No. 1 parking brake shoe assembly.

  9. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Front Side)


    1. A0004MOE04

      Using SST, install the parking brake shoe hold down compression spring.

      SST
      09718-00011

  10. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)


    1. A00084J

      Apply a small amount of high temperature grease to the areas shown in the illustration.

      Text in Illustration
      A0007SL High Temperature Grease

    2. Install the parking brake shoe return tension spring.

  11. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)


    1. Install the parking brake shoe return tension spring.

  12. CHECK PARKING BRAKE INSTALLATION


    1. Check that each part is installed properly.

      A0008REE01
      Text in Illustration
      *A LH Side *B RH Side
      A0005GR Front of the Vehicle - -

      Note

      There should be no oil or grease on the friction surfaces of the shoe linings or discs.

  13. INSTALL REAR DISC

    Click here

  14. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

  15. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  16. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL

    Click here

  17. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1049 kgf*cm, 76 ft.*lbf }

  18. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Connect the cable to the negative (-) auxiliary battery terminal Click here.

    2. Connect the reservoir level switch connector.

    3. Clear the DTCs Click here.

  19. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

    Click here

  20. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)

    Tech Tips

    Use the same procedure as for LHD Click here.