Click here

PARKING BRAKE ASSEMBLY DISASSEMBLY

Click here
Click here Click here

CAUTION / NOTICE / HINT

Note:

  • When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

  • While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

Tip:

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).

  2. Click here

    DISABLE BRAKE CONTROL

    Click here

  3. Click here

    REMOVE REAR WHEEL

  4. Click here

    SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  5. Click here

    REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

  6. Click here

    REMOVE REAR DISC

    Click here

  7. Click here

    REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)


    1. A0006KW

      Remove the parking brake shoe return tension spring.

  8. Click here

    REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)


    1. A0009KG

      Remove the parking brake shoe return tension spring.

  9. Click here

    REMOVE PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Front Side)


    1. A0004MOE04

      Using SST, remove the parking brake shoe hold down compression spring.

      09718-00011
  10. Click here

    REMOVE PARKING BRAKE SHOE STRUT


    1. A000810

      Pull the No. 1 parking brake shoe assembly towards the front of the vehicle by hand as shown in the illustration.

    2. A0003TP

      Remove the parking brake shoe strut.

  11. Click here

    REMOVE PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Rear Side)


    1. A0008EYE04

      Using SST, remove the parking brake shoe hold down compression spring.

      09718-00011
  12. Click here

    SEPARATE PARKING BRAKE SHOE LEVER


    1. A0007M2

      Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and pull downward to separate them from the parking brake plate.

    2. Separate the parking brake shoe lever from the No. 2 parking brake shoe assembly.

  13. Click here

    REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A0008X1

      Remove the parking brake shoe adjusting screw set.

  14. Click here

    REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A0003HC

      Remove the No. 1 parking brake shoe assembly.

  15. Click here

    REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)


    1. A0007Z2

      Remove the parking brake shoe return tension spring.

  16. Click here

    REMOVE PARKING BRAKE SHOE LEVER


    1. A000882

      Using needle-nose pliers, remove the parking brake shoe lever from the No. 3 parking brake cable assembly as shown in the illustration.

  17. Click here

    REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN


    1. A000935

      Remove the parking brake shoe hold down spring pin (for front side).

    2. A00081X

      Remove the parking brake shoe hold down spring pin (for rear side).