PARKING BRAKE CABLE INSTALLATION

PROCEDURE

1. Click here

   INSTALL NO. 2 PARKING BRAKE CABLE CLAMP

   
   

   1. Install a new No. 2 parking brake cable clamp to the No. 3 parking brake cable assembly.

2. Click here

   INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

   
   
   1. 

      Install the No. 3 parking brake cable assembly with the 4 bolts and nut.

      Bolt (A) and Nut
      8.5 N*m	87 kgf*cm	75 in.*lbf
      Bolt (B)
      6.0 N*m	61 kgf*cm	53 in.*lbf

   2. Install the No. 3 parking brake cable assembly with the bolt.

      8.0 N*m

      82 kgf*cm

      71 in.*lbf

   3. Install the clip to the No. 3 parking brake cable assembly.

3. Click here

   INSTALL NO. 2 FLOOR UNDER COVER (for LH Side)

   Click here

4. Click here

   INSTALL NO. 1 FLOOR UNDER COVER (for RH Side)

   Click here

5. Click here

   INSTALL PARKING BRAKE SHOE LEVER

   (Click here)

6. Click here

   INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR

   
   

   1. Install the front No. 2 floor heat insulator with the 3 nuts.

      4.9 N*m

      50 kgf*cm

      43 in.*lbf

7. Click here

   INSTALL FRONT EXHAUST PIPE ASSEMBLY

   (Click here)

8. Click here

   INSTALL NO. 4 PARKING BRAKE CABLE ASSEMBLY

   
   
   1. 

      Install the No. 4 parking brake cable assembly to the parking brake equalizer.

      Table 1. Text in Illustration

      *1	No. 4 Parking Brake Cable Assembly
      *2	Rubber Boot
      *3	Parking Brake Equalizer

   2. Slide the parking brake equalizer and rubber boot as shown in the illustration.

      Note:

      Make sure that the rubber boot is securely inserted into the groove of the No. 4 parking brake cable assembly.

   3. 

      Connect the No. 3 parking brake cable assembly to the parking brake equalizer.

      Table 2. Text in Illustration

      *1	Parking Brake Equalizer
      *2	No. 2 Parking Brake Cable Assembly
      *3	No. 3 Parking Brake Cable Assembly
      *4	No. 4 Parking Brake Cable Assembly

   4. Connect the No. 2 parking brake cable assembly to the parking brake equalizer.

9. Click here

   INSTALL NO. 4 CROSS MEMBER FLOOR REINFORCEMENT SUB-ASSEMBLY

   
   

   1. Install the No. 4 cross member floor reinforcement sub-assembly with the 8 bolts.

      19 N*m

      189 kgf*cm

      14 ft.*lbf

   2. Install the floor carpet.

10. Click here

    INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET

    
    

    1. Install the No. 2 console box mounting bracket with the 2 bolts.

    2. Engage the 2 clamps to install the wire harness to the No. 2 console box mounting bracket.

11. Click here

    INSTALL FRONT FLOOR CAUTION PLATE COVER

    Click here

12. Click here

    INSTALL FLOOR CARPET HOOK

    Click here

13. Click here

    INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET

    Click here

14. Click here

    INSTALL AUDIO AMPLIFIER COVER

    Click here

15. Click here

    INSTALL TELEMATICS TRANSCEIVER WITH MAYDAY BATTERY (w/ Telematics Transceiver)

    Click here

16. Click here

    INSTALL AUDIO AMPLIFIER COVER (w/ Telematics Transceiver)

    Click here

17. Click here

    INSTALL FRONT SEAT ASSEMBLY LH

    (Click here)

18. Click here

    INSTALL FRONT SEAT ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

19. Click here

    INSTALL CENTER PILLAR LOWER GARNISH LH

    Click here

20. Click here

    INSTALL REAR DOOR SCUFF PLATE LH

    Click here

21. Click here

    INSTALL CENTER PILLAR LOWER GARNISH RH

    Click here

22. Click here

    INSTALL REAR DOOR SCUFF PLATE RH

    Click here

23. Click here

    INSTALL COWL SIDE TRIM BOARD RH

    Tip:

    Use the same procedure as for the LH side (Click here).

24. Click here

    INSTALL FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure as for the LH side (Click here).

25. Click here

    INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)

    
    

    1. Pass the No. 1 parking brake cable assembly through the parking brake pedal assembly.

    2. Install the clip to the No. 1 parking brake cable assembly.

    3. Temporarily install the adjusting nut.

    4. 

       Bend the parking brake pedal claw.

26. Click here

    INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY (for RHD)

    
    

    1. Pass the No. 1 parking brake cable assembly through the parking brake pedal assembly.

    2. Install the clip to the No. 1 parking brake cable assembly.

    3. Temporarily install the adjusting nut.

    4. 

       Bend the parking brake pedal claw.

27. Click here

    INSTALL PARKING BRAKE PEDAL SUB-ASSEMBLY (for LHD)

    (Click here)

28. Click here

    INSTALL PARKING BRAKE PEDAL SUB-ASSEMBLY (for RHD)

    (Click here)