ELECTRONICALLY CONTROLLED BRAKE SYSTEM, Diagnostic DTC:C1247/47, C1346/71, C1392/48

DTC Code DTC Name
C1247/47 Stroke Sensor Malfunction
C1346/71 Stroke Sensor Zero Point Learning Malfunction (Test Mode DTC)
C1392/48 Stroke Sensor Zero Point Calibration Undone

DESCRIPTION

The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU (brake booster with master cylinder assembly).

DTC C1346/71 will be cleared when the brake pedal stroke sensor assembly sends a brake pedal stroke sensor assembly signal or when Test Mode ends. DTC C1346/71 is output only in Test Mode.

DTC No. INF Code DTC Detection Condition Trouble Area
C1247/47 211 Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.2 seconds or more.

  • Open or short in brake pedal stroke sensor assembly power supply circuit

  • Improperly connected connector, deformation or corrosion of terminals

  • Skid control ECU (Brake booster with master cylinder assembly)
↑ 212 Sensor output voltage 1 (SKS1) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.

  • Open or short in wire harness

  • Improperly connected connector, deformation or corrosion of terminals

  • Brake pedal stroke sensor assembly
↑ 213 Sensor output voltage 2 (SKS2) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCSK) for 0.2 seconds or more. ↑
↑ 214

Either of the following is detected:


  1. Fluctuation of sensor output 1 (SKS1) is out of specification.

  2. The difference between the present value and last value of sensor output voltage 1 (SKS1) is 8.5% or more (0.43 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.

 ↑
↑ 215

Either of the following is detected:


  1. Fluctuation of sensor output 2 (SKS2) is out of specification.

  2. The difference between the present value and last value of the sensor output voltage 2 (SKS2) is 8.5% or more (0.43 V or more) of the sensor supply voltage (VCM1) for 0.2 seconds or more.

 ↑
↑ 218 An excessive difference between the change in sensor output 1 (SKS1) and sensor output 2 (SKS2) is detected for 0.2 seconds or more. ↑
↑ 219

Sensor data is invalid for 0.2 seconds or more.

(Skid control ECU (Brake booster with master cylinder assembly) internal monitor circuit malfunction.)

 ↑
↑ 223

Sensor data is invalid for 0.2 seconds or more.

(Open, short, or noise.)

 ↑
C1392/48 - Zero point calibration of brake pedal stroke sensor assembly is unfinished.

  • Brake pedal stroke sensor zero point calibration incomplete (Initialization and calibration of linear solenoid valve incomplete)

  • Skid control ECU (Brake booster with master cylinder assembly)
C1346/71 - Detected only during Test Mode.

  • Brake pedal stroke sensor assembly

  • Brake pedal stroke sensor assembly circuit

WIRING DIAGRAM

A0009KVE62

CAUTION / NOTICE / HINT

Note

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform initialization and calibration of the linear solenoid valve Click here.

Tech Tips

Check the condition of each related circuit connector before troubleshooting Click here.

PROCEDURE


  1. CHECK BRAKE PEDAL


    1. Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.

    2. Check and adjust the brake pedal height (See page for LHD or Click here for RHD).

    3. Adjust the brake pedal stroke sensor assembly (See page for LHD or Click here for RHD).


    NEXT

  2. CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    2. Disconnect the A24 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A34 brake pedal stroke sensor assembly connector.

    4. Check both the connector case and the terminal for deformation and corrosion.

      OK
      No deformation or corrosion.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      A24-39 (VCSK) - A34-3 (VCSK) Always Below 1 Ω
      A24-39 (VCSK) - Body ground Always 10 kΩ or higher
      A24-41 (SKG) - A34-1 (SKG) Always Below 1 Ω
      A24-41 (SKG) - Body ground Always 10 kΩ or higher
      A24-42 (SKS) - A34-4 (SKS1) Always Below 1 Ω
      A24-42 (SKS) - Body ground Always 10 kΩ or higher
      A24-40 (SKS2) - A34-2 (SKS2) Always Below 1 Ω
      A24-40 (SKS2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      A24-39 (VCSK) - A34-3 (VCSK) Always Below 1 Ω
      A24-39 (VCSK) - Body ground Always 10 kΩ or higher
      A24-41 (SKG) - A34-1 (SKG) Always Below 1 Ω
      A24-41 (SKG) - Body ground Always 10 kΩ or higher
      A24-42 (SKS) - A34-2 (SKS1) Always Below 1 Ω
      A24-42 (SKS) - Body ground Always 10 kΩ or higher
      A24-40 (SKS2) - A34-4 (SKS2) Always Below 1 Ω
      A24-40 (SKS2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)


    1. A000697E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Brake Pedal Stroke Sensor Assembly)

      Reconnect the A24 skid control ECU (brake booster with master cylinder assembly) connector.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A34-3 (VCSK) - A34-1 (SKG) Power switch on (IG) 4.84 to 5.16 V
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG (for LHD) C
      NG (for RHD) D

    A

    REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY Click here

    B

    REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY Click here

    C

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Click here

    D

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Click here