REAR SUSPENSION MEMBER REMOVAL

PROCEDURE

1. Click here

   REMOVE REAR WHEELS

2. Click here

   REMOVE CENTER EXHAUST PIPE ASSEMBLY

   (Click here)

3. Click here

   REMOVE NO. 2 FLOOR UNDER COVER

   Click here

4. Click here

   REMOVE NO. 1 FLOOR UNDER COVER

   Click here

5. Click here

   REMOVE NO. 3 EXHAUST PIPE SUPPORT BRACKET

   
   
   1. 

      Remove the 2 bolts and No. 3 exhaust pipe support bracket from the rear suspension member sub-assembly.

6. Click here

   SEPARATE REAR STABILIZER LINK ASSEMBLY LH

   
   
   1. 

      Remove the nut and separate the rear stabilizer link assembly LH from the rear stabilizer bar.

      If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.

7. Click here

   SEPARATE REAR STABILIZER LINK ASSEMBLY RH

   Tip:

   Perform the same procedure as the LH side.

8. Click here

   REMOVE REAR STABILIZER BAR

   Click here

9. Click here

   REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

   (Click here)

10. Click here

    SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

11. Click here

    SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as the LH side.

12. Click here

    REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

13. Click here

    REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as the LH side.

14. Click here

    SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

15. Click here

    SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as the LH side.

16. Click here

    REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

17. Click here

    REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as the LH side.

18. Click here

    REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

    
    
    1. 

       Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

       Table 1. Text in Illustration

       *1	Engine Lifter
       *2	Attachment
       	Attachment Placement Location

       Note:
       

       • Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.

       • Use the attachments to keep the rear suspension member sub-assembly level.

    2. 

       Remove the 2 bolts, 4 nuts, rear suspension member lower stopper sub-assembly LH, rear suspension member lower stopper sub-assembly RH and 2 rear suspension member lower stoppers.

    3. Slowly lower the rear suspension member sub-assembly.

       Note:

       When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.

19. Click here

    REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH

    
    
    1. 

       Using SST and a press, remove the rear suspension member body mounting front cushion LH from the rear suspension member sub-assembly.

       09527-17011
       09950-60010	09951-00340
       09950-70010	09951-07100

20. Click here

    REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH

    Tip:

    Perform the same procedure as the LH side.

21. Click here

    REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)

    
    
    1. 

       Using SST and a press, remove the rear suspension member body mounting rear cushion from the rear suspension member sub-assembly.

       09527-17011
       09950-60010	09951-00340
       09950-70010	09951-07100

22. Click here

    REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

    Tip:

    Perform the same procedure as the LH side.

23. Click here

    REMOVE HOLE PLUG

    
    
    1. 

       Remove the 4 hole plugs from the rear suspension member sub-assembly.