FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) Power Seat Power Easy Access System Function does not Operate

DESCRIPTION

When the power switch is off and shift lever is in P, the power seat slides rearward when the seat belt tongue plate is disengaged from the front seat inner belt assembly (for driver) (auto away function). Also the power seat slides forward when the seat belt tongue plate is engaged to the front seat inner belt assembly (for driver) with the power switch on (ACC or IG), and shift lever is in P.

CAUTION / NOTICE / HINT

PROCEDURE

1. Click here

   CHECK FRONT POWER SEAT OPERATION

   
   

   1. Check that each function of the power seat operates normally by using the front power seat switch (for driver) (Click here).

      Result
      Result Proceed to Power seat functions operate normally A All power seat functions do not operate B One or more power seat motors do not operate C

   
   
   • AClick here
   • B

     GO TO OTHER DIAGNOSIS PROCEDURE (Front Power Seat does not Operate with Front Power Seat Switch) (Click here)

   • C

     GO TO OTHER DIAGNOSIS PROCEDURE (One or more Power Seat Motors do not Operate) (Click here)

2. Click here

   READ VALUE USING GTS

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the GTS on.

   4. Enter the following menus: Body Electrical / Driver Seat / Data List.

   5. Read the Data List according to the display on the GTS.

      Table 1. Driver Seat

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Driver Seat Buckle SW	Driver seat belt buckle switch / ON or OFF	ON: Driver seat belt fastened OFF: Driver seat belt unfastened	-

      OK
      On the GTS screen, the item changes between ON and OFF according to the above.

   
   
   • OKClick here
   • NGClick here
3. Click here

   CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - FRONT SEAT OUTER BELT ASSEMBLY (FOR DRIVER))

   
   

   1. Disconnect the P24*1 or Q22*2 front seat outer belt assembly (for driver) connector.

      
      

      • *1: for LHD

      • *2: for RHD

   2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Table 2. for LHD Tester Connection Condition Specified Condition P24-1 (IG) - Body ground Power switch on (IG) 11 to 14 V
      Table 3. for RHD Tester Connection Condition Specified Condition Q22-1 (IG) - Body ground Power switch on (IG) 11 to 14 V

   
   
   • OKClick here
   • NG

     REPAIR OR REPLACE HARNESS OR CONNECTOR

4. Click here

   CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT ASSEMBLY (FOR DRIVER) - FRONT POWER SEAT SWITCH (FOR DRIVER))

   
   

   1. Disconnect the X10*1 or W10*2 front power seat switch (for driver) connector.

      
      

      • *1: for LHD

      • *2: for RHD

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 4. for LHD Tester Connection Condition Specified Condition P24-2 (L) - X10-9 (DRDC) Always Below 1 Ω P24-2 (L) - Body ground Always 10 kΩ or higher
      Table 5. for RHD Tester Connection Condition Specified Condition Q22-2 (L) - W10-9 (DRDC) Always Below 1 Ω Q22-2 (L) - Body ground Always 10 kΩ or higher

   
   
   • OKClick here
   • NG

     REPAIR OR REPLACE HARNESS OR CONNECTOR

5. Click here

   CHECK SEAT BELT TENSION REDUCER SYSTEM

   
   

   1. Check that the seat belt tension reducer system (Click here).

      OK
      Seat belt tension reducer system is normal.

   
   
   • OKClick here
   • NG

     REPLACE FRONT SEAT OUTER BELT ASSEMBLY (FOR DRIVER)

6. Click here

   REPLACE FRONT POWER SEAT SWITCH (FOR DRIVER)

   
   

   1. Replace the front power seat switch (for driver) (Click here).

   
   
   • NEXTClick here
7. Click here

   CHECK POWER SEAT POWER EASY ACCESS SYSTEM

   
   

   1. Check that the power seat easy access system operates normally when engaging and disengaging the tongue plate of the seat belt with the shift lever in P (Click here).

      OK
      Power seat power easy access system is normal.

   
   
   • OK

     END (FRONT POWER SEAT SWITCH (FOR DRIVER) WAS DEFECTIVE)

   • NG

     REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

8. Click here

   INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)

   
   
   1. 

      Remove the front seat inner belt assembly (for driver) (Click here).

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 1 - 2 Driver seat belt unfastened 10 kΩ or higher 1 - 2 Driver seat belt fastened Below 1 Ω

      Table 6. Text in Illustration

      *a	Component without harness connected (Front Seat Inner Belt Assembly (for Driver))

   
   
   • OKClick here
   • NG

     REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER) (Click here)

9. Click here

   CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (FOR DRIVER) - FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER))

   
   

   1. Disconnect the X10*1 or W10*2 front power seat switch (for driver) connector.

      
      

      • *1: for LHD

      • *2: for RHD

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 7. for LHD Tester Connection Condition Specified Condition X10-10 (DBCL) - X16-1 Always Below 1 Ω X16-2 - Body ground Always Below 1 Ω X10-10 (DBCL) - Body ground Always 10 kΩ or higher
      Table 8. for RHD Tester Connection Condition Specified Condition W10-10 (DBCL) - W15-1 Always Below 1 Ω W15-2 - Body ground Always Below 1 Ω W10-10 (DBCL) - Body ground Always 10 kΩ or higher

   
   
   • OK

     REPLACE FRONT POWER SEAT SWITCH (FOR DRIVER) (Click here)

   • NG

     REPAIR OR REPLACE HARNESS OR CONNECTOR