Click here

FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) Wireless Transmitter Memory Function does not Operate

Click here
Click here
DTC Code DTC Name
  Wireless Transmitter Memory Function does not Operate
Click here

DESCRIPTION

With the power switch on (IG) and the driver door closed, pressing the manual lock or unlock switch on the multiplex network master switch assembly while holding a seat memory switch (M1 switch, M2 switch or M3 switch) will register the transmitter recognition code into the seat memory switch that was pressed. After registration is completed, the answer back buzzer sounds.

Click here

CAUTION / NOTICE / HINT

Note:

  • The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

  • If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

  • The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the communication system by checking the communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).

  • If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

Click here

PROCEDURE


  1. Click here

    CHECK POWER DOOR LOCK CONTROL SYSTEM


    1. Check the manual lock/unlock function by using the door control switch (multiplex network master switch assembly) (Click here).

      OK
      Manual lock/unlock function operates normally.

  2. Click here

    CHECK SMART ENTRY AND START SYSTEM (for Start Function)


    1. Check that the hybrid control system starts normally when the power switch is pressed with carrying the key and the brake pedal depressed.

      OK
      Hybrid control system starts normally.

  3. Click here

    CHECK SEAT POSITION MEMORY FUNCTION


    1. Store a seat position in memory (Click here).

    2. Check that the buzzer sounds for 0.5 seconds to indicate that a position has been stored.

      Note:

      • The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

      • If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

      OK
      Seat position memory function operates normally.

    • OKClick here
    • NG

      GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized) (Click here)

  4. Click here

    CHECK SEAT POSITION RESTORING FUNCTION


    1. Restore a memorized seat position (Click here).

    2. Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

      Note:

      • The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

      • If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

      OK
      Seat position restoring function operates normally.

    • OKClick here
    • NG

      GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position) (Click here)

  5. Click here

    READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Table 1. Main Body
      Tester Connection Measurement Item/Range Normal Condition Diagnostic Note
      FL Door Courtesy SW*1 Front door courtesy light switch assembly (for LH) signal / ON or OFF

      ON: Driver door open

      OFF: Driver door closed

      		 -
      FR Door Courtesy SW*2 Front door courtesy light switch assembly (for RH) signal / ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      		 -

      • *1: for LHD

      • *2: for RHD

      OK
      ON or OFF appears on the screen according to the driver door condition.

  6. Click here

    CHECK MEMORY CALL REGISTRATION FUNCTION


    1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.


      • Power switch is off

      • Press and hold the M1, M2 or M3 seat memory switch

      • Driver door closed

      • Carry the key

    2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration (Click here).

      OK
      Buzzer sounds normally.

  7. Click here

    READ VALUE USING GTS (MEMORY CALL REGISTRATION)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Table 2. Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Mem SW No. w/KeyID1 Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID1

      MEM SW1: M1 switch linked with key ID1

      MEM SW2: M2 switch linked with key ID1

      MEM SW3: M3 switch linked with key ID1

      		 -
      Mem SW No. w/KeyID2 Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID2

      MEM SW1: M1 switch linked with key ID2

      MEM SW2: M2 switch linked with key ID2

      MEM SW3: M3 switch linked with key ID2

      		 -
      Mem SW No. w/KeyID3 Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID3

      MEM SW1: M1 switch linked with key ID3

      MEM SW2: M2 switch linked with key ID3

      MEM SW3: M3 switch linked with key ID3

      		 -
      Mem SW No. w/KeyID4 Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID4

      MEM SW1: M1 switch linked with key ID4

      MEM SW2: M2 switch linked with key ID4

      MEM SW3: M3 switch linked with key ID4

      		 -
      Mem SW No. w/KeyID5 Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID5

      MEM SW1: M1 switch linked with key ID5

      MEM SW2: M2 switch linked with key ID5

      MEM SW3: M3 switch linked with key ID5

      		 -
      Mem SW No. w/KeyID6 Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID6

      MEM SW1: M1 switch linked with key ID6

      MEM SW2: M2 switch linked with key ID6

      MEM SW3: M3 switch linked with key ID6

      		 -
      Mem SW No. w/KeyID7 Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3

      NONE: No switches linked with key ID7

      MEM SW1: M1 switch linked with key ID7

      MEM SW2: M2 switch linked with key ID7

      MEM SW3: M3 switch linked with key ID7

      		 -
      OK
      On the GTS display, it is confirmed that the memory call has been registered.

  8. Click here

    CHECK MEMORY CALL FUNCTION


    1. Turn the power switch off.

    2. Close and lock all doors.

    3. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.

    4. Open the driver door and check that the driver seat moves to the memorized position (Click here).

      OK
      Driver seat moves to the memorized position.

    • OK

      USE SIMULATION METHOD TO CHECK (Click here)

    • NG

      GO TO OTHER DIAGNOSIS PROCEDURE (Wireless-linked Return Function does not Operate) (Click here)

  9. Click here

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    1. Replace the main body ECU (multiplex network body ECU) (Click here).


  10. Click here

    CHECK MEMORY CALL REGISTRATION FUNCTION


    1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.


      • Power switch is off

      • Press and hold the M1, M2 or M3 seat memory switch

      • Driver door closed

      • Carry the key

    2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration (Click here).

      OK
      Buzzer sounds normally.

    • OK

      END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

    • NGClick here
  11. Click here

    REPLACE FRONT POWER SEAT SWITCH (FOR DRIVER)


    1. Replace the front power seat switch (for driver) (Click here).


  12. Click here

    CHECK MEMORY CALL REGISTRATION FUNCTION


    1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.


      • Power switch is off

      • Press and hold the M1, M2 or M3 seat memory switch

      • Driver door closed

      • Carry the key

    2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration (Click here).

      OK
      Buzzer sounds normally.

    • OK

      END (FRONT POWER SEAT SWITCH (FOR DRIVER) WAS DEFECTIVE)

    • NG

      REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)