Click here

FRONT POWER SEAT CONTROL SYSTEM(w/ Memory), Diagnostic DTC:B2653

Click here
Click here
DTC Code DTC Name
B2653 Lifter Sensor Malfunction
Click here

DESCRIPTION

When the front power seat switch (for driver) or front power seat switch (for front passenger) do not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2653 The upward and downward lock detection position of the sensor is the same.

  • for Driver


    • Front power seat switch (for driver)


    • Lifter motor (front seat adjuster assembly (for driver))


    • Wire harness or connector


  • for Front Passenger


    • Front power seat switch (for front passenger)


    • Lifter motor (front seat adjuster assembly (for front passenger))


    • Wire harness or connector
Click here

WIRING DIAGRAM


Click here
  1. A00040NE25

    for Driver

  2. A00040NE26

    for Front Passenger

Click here

PROCEDURE


  1. Click here

    CHECK FOR DTC


    1. Check for DTCs (Click here).

      Result
      Result Proceed to
      DTC is not output A
      DTC output from "Driver Seat" B
      DTC output from "Passenger Seat" C

  2. Click here

    PERFORM ACTIVE TEST USING GTS (LIFTER MOTOR)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Driver Seat / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Table 1. Driver Seat
      Tester Display Test Part Control Range Diagnostic Note
      Lifter Operation Seat lifter operation OFF/Up/Down -
      OK
      Motor operates normally.

  3. Click here

    CHECK FRONT POWER SEAT SWITCH (FOR DRIVER) (LIFTER MOTOR CIRCUIT)


    1. Disconnect the X3*1 or W3*2 lifter motor connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Table 2. for LHD
      Tester Connection Condition Specified Condition
      X3-2 - X3-3 Lifter switch on 4.8 to 5.1 V
      Table 3. for RHD
      Tester Connection Condition Specified Condition
      W3-2 - W3-3 Lifter switch on 4.8 to 5.1 V

  4. Click here

    CHECK LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (FOR DRIVER))


    1. A0003V6E02

      Reconnect the X3*1 or W3*2 lifter motor connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Table 4. for LHD
      Tester Connection Condition Specified Condition
      X3-2 - Body ground Lifter switch on 4.5 to 4.8 V
      Table 5. for RHD
      Tester Connection Condition Specified Condition
      W3-2 - Body ground Lifter switch on 4.5 to 4.8 V
      Table 6. Text in Illustration
      *A for LHD
      *B for RHD
      *a

      Component with harness connected

      (Lifter Motor (Front Seat Adjuster Assembly (for Driver)))

    • OK

      REPLACE FRONT POWER SEAT SWITCH (FOR DRIVER) (Click here)

    • NG

      REPLACE LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (FOR DRIVER)) (Click here)

  5. Click here

    CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (FOR DRIVER) - LIFTER MOTOR)


    1. Disconnect the X10*1 or W10*2 front power seat switch (for driver) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 7. for LHD
      Tester Connection Condition Specified Condition
      X10-4 (SSRL) - X3-2 Always Below 1 Ω
      X10-1 (SGND) - X3-3 Always Below 1 Ω
      X10-4 (SSRL) - Body ground Always 10 kΩ or higher
      X10-1 (SGND) - Body ground Always 10 kΩ or higher
      Table 8. for RHD
      Tester Connection Condition Specified Condition
      W10-4 (SSRL) - W3-2 Always Below 1 Ω
      W10-1 (SGND) - W3-3 Always Below 1 Ω
      W10-4 (SSRL) - Body ground Always 10 kΩ or higher
      W10-1 (SGND) - Body ground Always 10 kΩ or higher

    • OK

      REPLACE FRONT POWER SEAT SWITCH (FOR DRIVER) (Click here)

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    INSPECT LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (FOR DRIVER))


    1. A0007P8E14

      Disconnect the X3*1 or W3*2 lifter motor connector.


      • *1: for LHD

      • *2: for RHD

    2. Check if the seat cushion moves smoothly when the auxiliary battery is connected to the lifter motor connector terminals.

      OK
      Condition Operational Direction

      Auxiliary battery positive (+) → Terminal 4

      Auxiliary battery negative (-) → Terminal 1

      		 Seat cushion moves downward

      Auxiliary battery positive (+) → Terminal 1

      Auxiliary battery negative (-) → Terminal 4

      		 Seat cushion moves upward
      Table 9. Text in Illustration
      *a

      Component without harness connected

      (Lifter Motor (Front Seat Adjuster Assembly (for Driver)))

  7. Click here

    CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (FOR DRIVER) - LIFTER MOTOR)


    1. Disconnect the X9*1 or W9*2 front power seat switch (for driver) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 10. for LHD
      Tester Connection Condition Specified Condition
      X9-10 (LFT+) - X3-1 Always Below 1 Ω
      X9-12 (LFT-) - X3-4 Always Below 1 Ω
      X9-10 (LFT+) - Body ground Always 10 kΩ or higher
      X9-12 (LFT-) - Body ground Always 10 kΩ or higher
      Table 11. for RHD
      Tester Connection Condition Specified Condition
      W9-10 (LFT+) - W3-1 Always Below 1 Ω
      W9-12 (LFT-) - W3-4 Always Below 1 Ω
      W9-10 (LFT+) - Body ground Always 10 kΩ or higher
      W9-12 (LFT-) - Body ground Always 10 kΩ or higher

    • OK

      REPLACE FRONT POWER SEAT SWITCH (FOR DRIVER) (Click here)

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. Click here

    PERFORM ACTIVE TEST USING GTS (LIFTER MOTOR)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Passenger Seat / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Table 12. Passenger Seat
      Tester Display Test Part Control Range Diagnostic Note
      Lifter Operation Seat lifter operation OFF/Up/Down -
      OK
      Motor operates normally.

  9. Click here

    CHECK FRONT POWER SEAT SWITCH (FOR FRONT PASSENGER) (LIFTER MOTOR CIRCUIT)


    1. Disconnect the W3*1 or X3*2 lifter motor connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Table 13. for LHD
      Tester Connection Condition Specified Condition
      W3-2 - W3-3 Lifter switch on 4.8 to 5.1 V
      Table 14. for RHD
      Tester Connection Condition Specified Condition
      X3-2 - X3-3 Lifter switch on 4.8 to 5.1 V

  10. Click here

    CHECK LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (FOR FRONT PASSENGER))


    1. A00062AE02

      Reconnect the W3*1 or X3*2 lifter motor connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Table 15. for LHD
      Tester Connection Condition Specified Condition
      W3-2 - Body ground Lifter switch on 4.5 to 4.8 V
      Table 16. for RHD
      Tester Connection Condition Specified Condition
      X3-2 - Body ground Lifter switch on 4.5 to 4.8 V
      Table 17. Text in Illustration
      *A for LHD
      *B for RHD
      *a

      Component with harness connected

      (Lifter Motor (Front Seat Adjuster Assembly (for Front Passenger)))

    • OK

      REPLACE FRONT POWER SEAT SWITCH (FOR FRONT PASSENGER) (Click here)

    • NG

      REPLACE LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (FOR FRONT PASSENGER)) (Click here)

  11. Click here

    CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (FOR FRONT PASSENGER) - LIFTER MOTOR)


    1. Disconnect the W10*1 or X10*2 front power seat switch (for front passenger) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 18. for LHD
      Tester Connection Condition Specified Condition
      W10-4 (SSRL) - W3-2 Always Below 1 Ω
      W10-1 (SGND) - W3-3 Always Below 1 Ω
      W10-4 (SSRL) - Body ground Always 10 kΩ or higher
      W10-1 (SGND) - Body ground Always 10 kΩ or higher
      Table 19. for RHD
      Tester Connection Condition Specified Condition
      X10-4 (SSRL) - X3-2 Always Below 1 Ω
      X10-1 (SGND) - X3-3 Always Below 1 Ω
      X10-4 (SSRL) - Body ground Always 10 kΩ or higher
      X10-1 (SGND) - Body ground Always 10 kΩ or higher

    • OK

      REPLACE FRONT POWER SEAT SWITCH (FOR FRONT PASSENGER) (Click here)

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. Click here

    INSPECT LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (FOR FRONT PASSENGER))


    1. A0007P8E14

      Disconnect the W3*1 or X3*2 lifter motor connector.


      • *1: for LHD

      • *2: for RHD

    2. Check if the seat cushion moves smoothly when the auxiliary battery is connected to the lifter motor connector terminals.

      OK
      Condition Operational Direction

      Auxiliary battery positive (+) → Terminal 4

      Auxiliary battery negative (-) → Terminal 1

      		 Seat cushion moves downward

      Auxiliary battery positive (+) → Terminal 1

      Auxiliary battery negative (-) → Terminal 4

      		 Seat cushion moves upward
      Table 20. Text in Illustration
      *a

      Component without harness connected

      (Lifter Motor (Front Seat Adjuster Assembly (for Front Passenger)))

    • OKClick here
    • NG

      REPLACE LIFTER MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (FOR FRONT PASSENGER)) (Click here)

  13. Click here

    CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (FOR FRONT PASSENGER) - LIFTER MOTOR)


    1. Disconnect the W9*1 or X9*2 front power seat switch (for front passenger) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 21. for LHD
      Tester Connection Condition Specified Condition
      W9-10 (LFT+) - W3-1 Always Below 1 Ω
      W9-12 (LFT-) - W3-4 Always Below 1 Ω
      W9-10 (LFT+) - Body ground Always 10 kΩ or higher
      W9-12 (LFT-) - Body ground Always 10 kΩ or higher
      Table 22. for RHD
      Tester Connection Condition Specified Condition
      X9-10 (LFT+) - X3-1 Always Below 1 Ω
      X9-12 (LFT-) - X3-4 Always Below 1 Ω
      X9-10 (LFT+) - Body ground Always 10 kΩ or higher
      X9-12 (LFT-) - Body ground Always 10 kΩ or higher

    • OK

      REPLACE FRONT POWER SEAT SWITCH (FOR FRONT PASSENGER) (Click here)

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR