ПЕРЕДНИЙ ПРИВОДНОЙ ВАЛ В СБОРЕ (для моделей с 1AD-FTV, 2AD-FHV) РАЗБОРКА


  1. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH


    1. A01INCI

      Using a screwdriver, remove the hole snap ring.

  2. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH


    1. A01IUD5

      Using needle-nose pliers, remove the inboard joint boot clamp as shown in the illustration.

  3. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  4. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP LH


    1. A01INRE

      for 1AD-FTV:

      Using pliers, remove the outboard joint boot clamp as shown in the illustration.

    2. A01IQAR

      for 2AD-FHV:

      Using needle-nose pliers, remove the inboard joint boot clamp as shown in the illustration.

  5. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  6. REMOVE FRONT AXLE INBOARD JOINT BOOT LH


    1. Remove the boot from the inboard joint.

  7. REMOVE FRONT AXLE INBOARD JOINT BOOT RH

    Tech Tips

    Use the same procedures described for the LH side.

  8. REMOVE FRONT DRIVE INBOARD JOINT LH


    1. A01ITV5E07
      Text in Illustration
      *1 Matchmark

      Remove any old grease from the inboard joint.

    2. Put matchmarks on the inboard joint and outboard joint shaft.

      Note

      Do not punch the marks.

    3. Remove the inboard joint from the outboard joint shaft.

  9. REMOVE FRONT DRIVE INBOARD JOINT RH

    Tech Tips

    Use the same procedures described for the LH side.

  10. REMOVE FRONT DRIVE INNER SHAFT INNER SHAFT SNAP RING LH


    1. A01ISC0E01
      Text in Illustration
      *A for 1AD-FTV
      *B for 2AD-FHV

      Using a snap ring expander, remove the shaft snap ring.

    2. A01IN8NE01
      Text in Illustration
      *1 Matchmark

      Put matchmarks on the outboard joint shaft and tripod.

    3. Using a brass bar and hammer, tap off the tripod from the outboard joint shaft.

      Note

      Do not tap the rollers.

    4. Remove the inboard joint boot and inboard joint boot clamp.

  11. REMOVE FRONT DRIVE INNER SHAFT INNER SHAFT SNAP RING RH

    Tech Tips

    Use the same procedures described for the LH side.

  12. REMOVE FRONT DRIVE SHAFT DAMPER CLAMP LH


    1. A01IPT1

      for 1AD-FTV:

      Using pliers, remove the drive shaft damper clamp, as shown in the illustration.

    2. A01IPJ3

      for 2AD-FHV:

      Using needle-nose pliers, remove the drive shaft damper clamp, as shown in the illustration.

  13. REMOVE FRONT DRIVE SHAFT DAMPER LH


    1. Remove the front drive shaft damper from the outboard joint shaft.

  14. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH


    1. A01IO9L

      Using pliers, remove the outboard joint boot clamp as shown in the illustration.

  15. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  16. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH


    1. A01INJR

      Using pliers, remove the outboard joint boot clamp as shown in the illustration.

  17. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedures described for the LH side.

  18. REMOVE FRONT AXLE OUTBOARD JOINT BOOT LH


    1. Remove the outboard joint boot from the outboard joint shaft.

    2. Remove any old grease from the outboard joint.

  19. REMOVE FRONT AXLE OUTBOARD JOINT BOOT RH

    Tech Tips

    Use the same procedures described for the LH side.

  20. REMOVE FRONT DRIVE SHAFT DUST COVER LH


    1. A01IS2RE04

      Using SST and a press, press out the inboard joint to remove the dust cover.

      SST
      09950-00020

      Note

      Be careful not to drop the inboard joint.

  21. REMOVE FRONT DRIVE SHAFT DUST COVER RH

    Tech Tips

    Use the same procedures described for the LH side.