ЖГУТ ЭЛЕКТРОПРОВОДКИ ТРАНСМИССИИ УСТАНОВКА


  1. INSTALL TRANSMISSION WIRE

    A01IP1NE01

    1. Coat the O-ring of the transmission wire connector with ATF.

    2. Coat the bolt with ATF.

    3. Install the transmission wire to the valve body with the lock plate and bolt.

      Torque:
      11 N*m  { 110 kgf*cm, 8 ft.*lbf }

    4. Attach the transmission wire to the wire harness clamp and connect the 9 connectors.

  2. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    1. Coat the O-ring of the transmission wire connector with ATF.

    2. Align the groove of the manual valve with the manual valve lever.

    3. A01INQDE02

      Install the valve body to the transaxle case with the 11 bolts.

      Note


      • When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case to interfere with each other.

      • Temporarily install the bolts marked *1 in the illustration first because they are positioning bolts.

      Torque:
      11 N*m  { 110 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Each bolt length is indicated below.

      Bolt A: 25 mm (0.984 in.)

      Bolt B: 30 mm (1.18 in.)

      Bolt C: 35 mm (1.38 in.)

      Bolt D: 45 mm (1.77 in.)

      Bolt E: 55 mm (2.17 in.)

  3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

    A01IQS1

    1. Coat a new O-ring with ATF and install it to the oil strainer.

      Note

      Ensure that the O-ring is not twisted or pinched.

    2. A01IT74

      Install the oil strainer to the valve body with the 2 bolts.

      Torque:
      11 N*m  { 110 kgf*cm, 8 ft.*lbf }

  4. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

    A01IP69E05

    1. Install the 2 magnets to the oil pan.

      Text in Illustration
      *1 Magnet

    2. Install a new gasket to the oil pan.

    3. A01IQ7UE01

      Apply seal packing to the bolt labeled A in the illustration.

      Seal packing
      Toyota Genuine Seal Packing 1281,
      Three Bond 1281 or equivalent

    4. Install the oil pan to the automatic transaxle with the 18 bolts.

      Torque:
      for bolt labeled A
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }
      for other bolts
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

      Note


      • In order to ensure proper sealing of the transmission oil pan bolt, apply seal packing to the bolt and install it within 10 minutes of seal packing application.

      • Completely remove any oil or grease from the contact surfaces of the transaxle case, oil pan sub-assembly and gasket before installation.

  5. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

    A01IRC7

    1. Install the front suspension member reinforcement with the 4 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

  6. ADD AUTOMATIC TRANSAXLE FLUID


    1. Add automatic transaxle fluid Click here.

  7. INSTALL REAR ENGINE UNDER COVER LH


    1. Закрепите защиту картера 5 фиксаторами.

  8. INSTALL NO. 1 ENGINE UNDER COVER


    1. A01IRQL

      Install the No. 1 engine under cover with the 10 clips and 6 bolts.