МАСЛО И МАСЛЯНЫЙ ФИЛЬТР ЗАМЕНА

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.


  1. REMOVE NO. 1 ENGINE UNDER COVER


    1. A01IUJJ

      Remove the 9 clips and fold back the No. 1 engine under cover.

      Tech Tips

      It is not necessary to fully remove the No. 1 engine under cover. Partially remove it so that the oil filter element can be removed in a later step.

  2. DRAIN ENGINE OIL


    1. Remove the oil filler cap sub-assembly.

    2. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    3. Install a new gasket and the oil pan drain plug.

      Torque:
      38 N*m  { 387 kgf*cm, 28 ft.*lbf }

  3. REMOVE OIL FILTER ELEMENT


    1. A01INHEE08
      Text in Illustration
      *1 Oil filter drain pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the oil filter drain pipe.

    2. A01IPQG

      Remove the oil filter drain plug.

    3. Remove the O-ring from the oil filter drain plug and install it to an oil filter drain pipe.

    4. A01IQO9E01
      Text in Illustration
      *1 Oil Filter Cap
      *2 O-Ring
      *3 Oil Filter Drain Pipe

      Install the oil filter drain pipe to the oil filter cap and drain the engine oil.

    5. Remove the oil filter drain pipe.

    6. Apply a light coat of engine oil to a new O-ring and install it to the oil filter drain plug.

    7. Install the oil filter drain plug to the oil filter cap.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }
    8. A01ITUTE01

      Using SST, remove the oil filter cap.

      SST
      09228-06501
    9. A01ITLEE01
      Text in Illustration
      *1 Oil Filter Element
      *2 O-Ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Be sure to remove the cap O-ring by hand without using any tools to prevent damage to the cap O-ring groove.

  4. INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, its threads and its O-ring groove.

    2. A01IN35E01
      Text in Illustration
      *1 O-Ring
      *a CORRECT
      *b INCORRECT

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element in the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    6. A01IOH3E01
      Text in Illustration
      *1 Oil Filter Cap
      *2 O-Ring
      *3 Oil Filter Bracket
      *a No Gap

      Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

  5. ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      ACEA C2

      - 0W-30

      - 5W-30
      Standard Capacity
      Item Specified Condition
      Drain and refill without oil filter change 5.5 liters (5.8 US qts, 4.8 Imp. qts)
      Drain and refill with oil filter change 5.9 liters (6.2 US qts, 5.2 Imp. qts)
      Dry fill 6.3 liters (6.7 US qts, 5.5 Imp. qts)

  6. INSPECT FOR OIL LEAK


    1. Warm up the engine and check for an engine oil leak.

  7. INSPECT ENGINE OIL LEVEL


    1. Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.

      If low, check for leakage and add oil up to the full level mark.

      Note

      Do not fill engine oil above the full level mark.

  8. INSTALL NO. 1 ENGINE UNDER COVER


    1. A01IQXZ

      Install the No. 1 engine under cover with the 9 clips.