КОНТАКТНЫЙ ДАТЧИК ДАВЛЕНИЯ МАСЛА УСТАНОВКА


  1. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY


    1. Remove the adhesive from the threads of the oil pressure switch assembly and the bolt hole of the No. 1 oil cooler bracket.

    2. A01IQK9E01
      Text in Illustration
      *1 Adhesive

      Apply adhesive to 2 or 3 threads of the oil pressure switch assembly.

      Adhesive
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

      Note

      Do not apply adhesive to the oil inlet port of the engine oil pressure switch assembly.

    3. Using a 24 mm deep socket wrench, install the engine oil pressure switch assembly.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

      Note

      Do not start the engine for at least 1 hour after installation.

    4. Connect the engine oil pressure switch connector.

  2. ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Item Oil Grade Oil Viscosity (SAE)

      for CCo:

      Diesel fuel that contains between 50 ppm and 500 ppm of sulfur

      G-DLD1, ACEA B1, API CF-4 or CF

      (You may also use API CE or CD)

      - 5W-30

      - 10W-30

      - 15W-40

      - 20W-50

      for CCo:

      Diesel fuel that contains 50 ppm or less of sulfur

      		 ACEA C2, ACEA B1, API CF-4 or CF

      - 0W-30

      - 5W-30

      - 10W-30

      - 15W-40

      - 20W-50
      for DPF ACEA C2

      - 0W-30

      - 5W-30
      Standard Capacity (for CCo)
      Item Specified Condition
      Drain and refill without oil filter change 5.9 liters (6.2 US qts, 5.2 Imp. qts)
      Drain and refill with oil filter change 6.3 liters (6.7 US qts, 5.5 Imp. qts)
      Dry fill 7.1 liters (7.5 US qts, 6.2 Imp. qts)
      Standard Capacity (for DPF)
      Item Specified Condition
      Drain and refill without oil filter change 5.5 liters (5.8 US qts, 4.8 Imp. qts)
      Drain and refill with oil filter change 5.9 liters (6.2 US qts, 5.2 Imp. qts)
      Dry fill 6.7 liters (7.1 US qts, 5.9 Imp. qts)

  3. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  4. INSPECT ENGINE OIL LEVEL


    1. Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.

      If low, check for leakage and add oil up to the full level mark.

      Note

      Do not fill engine oil above the full level mark.

      Tech Tips

      A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.


      • When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.

      • If low quality oil or oil of an inappropriate viscosity is used.

      • When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.

      • When leaving the idling for a long time, or when driving frequently through heavy traffic.

      When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.

  5. INSTALL RADIATOR SUPPORT OPENING COVER


    1. Установите крышку отверстия кронштейна радиатора и введите в зацепление 4 крюка.

    2. Установите 3 фиксатора.

  6. INSTALL NO. 1 ENGINE COVER


    1. A01INMI

      Введите в зацепление 4 фиксатора, чтобы закрепить крышку двигателя № 1.

  7. INSTALL NO. 1 ENGINE UNDER COVER


    1. A01IQXZ

      Install the No. 1 engine under cover with the 9 clips.