Click here

ВПУСКНОЙ КОЛЛЕКТОР СНЯТИЕ

Click here
Click here
Note:

  • When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.

  • When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.

Click here
  1. Click here

    REMOVE DIESEL THROTTLE BODY ASSEMBLY

    (Click here)

  2. Click here

    DISCONNECT ENGINE WIRE


    1. Disconnect the fuel pressure sensor connector.

    2. Disconnect the pressure discharge valve connector.

    3. Remove the screw grommet and nut, and disconnect the glow plug wire harness.

    4. Detach the 2 wire harness clamps.

    5. Remove the bolt and wire harness bracket.

    6. Remove the bolt and 3 nuts, and disconnect the engine wire.

  3. Click here

    REMOVE EGR VALVE BRACKET


    1. A01IPQ0

      Disconnect the 2 connectors and detach the 2 wire harness clamps.

    2. A01IPI2

      Remove the 3 bolts and 2 EGR valve brackets.

  4. Click here

    REMOVE NO. 7 WATER BY-PASS HOSE

  5. Click here

    DISCONNECT NO. 8 WATER BY-PASS HOSE

  6. Click here

    REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY


    1. A01IOQA

      Disconnect the electric EGR control valve connector.

    2. A01IPRKE01

      Remove the 3 bolts, 2 nuts, No. 2 EGR pipe and 2 gaskets.

      Table 1. Text in Illustration
      *1 Nut
  7. Click here

    REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY


    1. A01IQP8

      Remove the electric EGR control valve and gasket.

  8. Click here

    REMOVE FUEL INLET PIPE SUB-ASSEMBLY

    Note:

    After removing the fuel inlet pipe, cover the common rail and supply pump with electrical tape to prevent dirt from entering them.


    1. A01ITN1

      Remove the nut and 2 clamps.

    2. Using a 14 mm union nut wrench, remove the fuel inlet pipe.

  9. Click here

    REMOVE INJECTION PIPE SUB-ASSEMBLY

    Note:

    After removing the injection pipe, to prevent dirt or foreign objects from entering the pipe inlet, cover the common rail with electrical tape. Also protect the injector inlets with electrical tape or plastic bags.


    1. A01IO2G

      Remove the 2 bolts and 4 injection pipe clamps.

    2. Using a 14 mm union nut wrench, loosen the 4 nuts at the common rail end of the injection pipes.

    3. Using a 14 mm union nut wrench, loosen the 4 nuts at the injector end of the injection pipes.

    4. Remove the 4 injection pipes.

  10. Click here

    REMOVE COMMON RAIL ASSEMBLY


    1. A01IUFT

      Using pliers, grip the claws of the clip and slide the clip to disconnect the fuel hose.

    2. Remove the 2 bolts and common rail.

  11. Click here

    REMOVE INTAKE MANIFOLD INSULATOR


    1. A01IQK4

      Remove the intake manifold insulator from the intake manifold.

  12. Click here

    REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Remove the engine oil level dipstick.

    2. A01IMYE

      Disconnect the connector and detach the wire harness clamp from the engine oil level dipstick guide.

    3. Remove the 2 bolts and engine oil level dipstick guide.

    4. Remove the O-ring from the engine oil level dipstick guide.

  13. Click here

    REMOVE DIESEL TURBO PRESSURE SENSOR


    1. A01IQ0K

      Disconnect the vacuum hose.

    2. Remove the bolt and sensor.

  14. Click here

    REMOVE NO. 1 GAS FILTER


    1. A01IQMA

      Disconnect the vacuum hose.

    2. Remove the No. 1 gas filter from the gas filter bracket.

  15. Click here

    REMOVE GAS FILTER BRACKET


    1. A01ITRH

      Remove the 2 bolts and gas filter bracket.

  16. Click here

    REMOVE ENGINE COVER BRACKET


    1. A01INXS

      Remove the bolt and engine cover bracket.

  17. Click here

    REMOVE NO. 2 INTAKE MANIFOLD


    1. A01IPPN

      Remove the bolt, 2 nuts, No. 2 intake manifold and gasket.

  18. Click here

    DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE


    1. A01IPLK

      Disconnect the No. 2 vacuum transmitting hose from the intake manifold.

  19. Click here

    REMOVE INTAKE MANIFOLD


    1. A01IOHHE01

      Remove the 7 bolts, 2 nuts, intake manifold and gasket.

      Table 2. Text in Illustration
      *1 Nut

    2. Remove the gasket from the cylinder head.

  20. Click here

    REPLACE STUD BOLT

    Tip:

    If a stud bolt is deformed or the threads are damaged, replace it.


    1. A01IQH0E01

      Replace the 2 stud bolts.

      9.0 N*m 92 kgf*cm 80 in.*lbf