ОХЛАДИТЕЛЬ РОГ СНЯТИЕ


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

  4. REMOVE NO. 1 ENGINE UNDER COVER


    1. A01IR30

      Выверните 6 болтов и снимите 11 фиксаторов.

    2. Снимите нижнюю крышку двигателя № 1.

  5. DRAIN ENGINE COOLANT

    CAUTION:

    Не снимайте пробку расширительного бачка радиатора и клапан для выпуска воздуха, пока двигатель и радиатор не остынут. Выброс горячей охлаждающей жидкости и пара под давлением может стать причиной серьезных ожогов.


    1. Ослабьте пробку сливного крана радиатора и слейте охлаждающую жидкость двигателя.

      A01IUCQE01
      Обозначения на рисунке
      *1 Пробка расширительного бачка *2 Клапан для выпуска воздуха
      *3 Пробка сливного крана радиатора - -

      Tech Tips

      Слейте охлаждающую жидкость в резервуар и утилизируйте ее в соответствии с местными требованиями.

    2. Снимите пробку расширительного бачка.

  6. REMOVE RADIATOR SUPPORT OPENING COVER


    1. A01IPK0

      Снимите 3 фиксатора.

    2. Открепите 4 крюка и снимите крышку отверстия кронштейна радиатора.

  7. REMOVE BATTERY CLAMP SUB-ASSEMBLY


    1. A01ININ

      Remove the bolt and loosen the nut.

    2. Detach the hook of the battery clamp sub-assembly from the battery carrier, and then remove the battery clamp sub-assembly.

  8. REMOVE BATTERY INSULATOR

  9. REMOVE BATTERY

  10. REMOVE BATTERY TRAY

  11. REMOVE BATTERY CARRIER


    1. A01IQXM

      Detach the 2 clamps and disconnect the engine wire.

    2. Remove the 4 bolts and battery carrier.

  12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE ASSEMBLY


    1. A01IT1KE01
      Text in Illustration
      *1 Retainer

      Detach the clamp and disconnect the mass air flow meter sub-assembly connector.

    2. Detach the clamp and disconnect the vacuum hose from the air cleaner hose assembly.

    3. Detach the clamp and disconnect the No. 1 fuel hose from the air cleaner hose assembly.

    4. Detach the clamp and disconnect the No. 2 fuel hose from the air cleaner hose assembly.

    5. Disconnect the ventilation hose from the cylinder head cover sub-assembly.

    6. Release the retainer and disconnect the air cleaner hose assembly from the turbocharger sub-assembly as shown in the illustration.

    7. Detach the 2 clamps and remove the air cleaner cap sub-assembly with air cleaner hose assembly.

  13. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  14. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    1. A01IN4S

      Remove the 3 bolts and air cleaner case sub-assembly.

  15. DISCONNECT COMPRESSOR OUTLET ELBOW


    1. A01IQQ6E01
      Text in Illustration
      *1 Retainer

      Release the retainer and disconnect the compressor outlet elbow from the turbocharger sub-assembly as shown in the illustration.

  16. DISCONNECT ENGINE WIRE


    1. A01IQ1V

      Detach the 2 clamps from the No. 1 air tube assembly.

    2. Remove the 2 bolts and disconnect the engine wire from the No. 1 air tube assembly.

  17. REMOVE NO. 4 WATER BY-PASS HOSE


    1. A01IQ3QE01
      Text in Illustration
      *1 Retainer

      Release the retainer and disconnect the No. 4 water by-pass hose from the EGR cooler assembly as shown in the illustration.

    2. Slide the clamp and remove the No. 4 water by-pass hose from the No. 2 radiator pipe.

  18. DISCONNECT NO. 1 AIR TUBE ASSEMBLY


    1. A01IN8C

      Slide the clamp and disconnect the water by-pass hose assembly from the No. 2 radiator pipe.

    2. Slide the clamp and disconnect the radiator hose sub-assembly from the No. 1 radiator pipe.

    3. Detach the clamp and disconnect the water hose sub-assembly from the compressor outlet elbow.

    4. Slide the clamp and disconnect the water hose sub-assembly from the No. 1 radiator pipe.

    5. Slide the clamp and disconnect the outlet heater water hose from the No. 2 radiator pipe.

    6. Remove the 2 bolts and disconnect the No. 1 air tube assembly from the manual transaxle assembly.

  19. DISCONNECT FUEL FEED PIPE SUB-ASSEMBLY


    1. A01IS7O

      Detach the 2 clamps and disconnect the engine wire.

    2. A01ITOL

      Remove the 2 bolts and disconnect the fuel feed pipe sub-assembly.

    3. A01IOX3

      Disconnect the vacuum hose from the No. 2 fuel hose.

    4. Disconnect the fuel feed pipe sub-assembly from the fuel pipe clamp.

  20. REMOVE NO. 1 TURBO INSULATOR


    1. A01IQ49

      Remove the 3 bolts, nut and No. 1 turbo insulator.

  21. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    1. A01ITIP

      Disconnect the air fuel ratio sensor connector.

    2. Raise the air fuel ratio sensor connector to remove the air fuel ratio sensor connector from the bracket.

    3. Detach the 2 clamps and disconnect the air fuel ratio sensor.

    4. Detach the 2 clamps and disconnect the engine wire.

  22. REMOVE EGR COOLER ASSEMBLY WITH EGR VALVE ASSEMBLY


    1. A01IUSY

      Disconnect the EGR valve assembly connector.

    2. Detach the clamp and disconnect the engine wire from the EGR valve assembly.

    3. Disconnect the hose clamp from the EGR cooler hose.

    4. A01IQK7

      Disconnect the vacuum hose from the EGR cooler assembly.

    5. A01ITBTE01

      Remove the 7 bolts and EGR cooler assembly with EGR valve assembly.

      Tech Tips


      • When removing the bolts labeled A, use a T45 "TORX" socket wrench.

      • When removing the bolts labeled B, use a 6 mm hexagon wrench.

      • The bolt labeled C in the illustration cannot be removed from the intake manifold.

    6. Remove the gasket.

    7. A01IPEN

      Remove the water pipe from the EGR cooler assembly.

  23. REMOVE EGR VALVE ASSEMBLY


    1. A01ITI7

      Remove the grommet from the EGR cooler assembly.

    2. Using pliers, grasp the 4 EGR cooler hose clamps and move the 4 EGR cooler hose clamps as shown in the illustration to remove the 2 EGR cooler hoses from the EGR cooler assembly and EGR valve assembly.

      A01ITVWE01
    3. A01ISTM

      Using a T30H "TORX" socket wrench, remove the 2 bolts, EGR valve assembly and gasket.