ДАТЧИК УРОВНЯ ТОПЛИВА В СБОРЕ СНЯТИЕ


  1. REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)

    Click here

  2. REMOVE REAR CENTER SEAT ASSEMBLY (w/ Rear No. 1 Seat)

    Click here

  3. REMOVE REAR FLOOR SERVICE HOLE COVER


    1. A01IUNL

      Remove the butyl tape and rear floor service hole cover.

    2. Disconnect the fuel sender gauge assembly connector.

  4. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. A01ISQRE01
      Text in Illustration
      *1 Fuel Tank Main Tube Sub-assembly
      *2 Tube Joint Clip
      *3 O-Ring
      *4 Fuel Tank Vent Tube Sub-assembly

      Remove the tube joint clip and pull out the fuel tank main tube sub-assembly.

      Note


      • Remove any dirt and foreign matter on the fuel tube joint before performing this step.

      • Do not scratch or allow any foreign matter to adhere to the parts when disconnecting them as the fuel tube joint contains the O-rings that seal the plug.

      • Perform this step by hand. Do not use any tools.

      • Do not forcibly bend or twist the nylon tube.

      • Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tank main tube sub-assembly.

  5. DISCONNECT FUEL TANK RETURN TUBE SUB-ASSEMBLY


    1. A01IO3VE01
      Text in Illustration
      *1 Fuel Tank Return Tube Sub-assembly
      *2 Tube Joint Clip
      *3 O-Ring
      *4 Fuel Tank Vent Tube Sub-assembly

      Remove the tube joint clip and pull out the fuel tank return tube sub-assembly.

      Note


      • Remove any dirt and foreign matter on the fuel tube joint before performing this work.

      • Do not scratch or allow any foreign matter to adhere to the parts when disconnecting them as the fuel tube joint contains the O-rings that seal the plug.

      • Perform this step by hand. Do not use any tools.

      • Do not forcibly bend or twist the nylon tube.

      • Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tank main tube sub-assembly.

  6. REMOVE TANK SUCTION TUBE SUPPORT


    1. A01IQI8

      Detach the 2 claws and remove the tank suction tube support.

  7. REMOVE FUEL PUMP GAUGE RETAINER

    CAUTION:

    Due to swelling of the fuel tank assembly, the tightening torque of the fuel pump gauge retainer may be as high as 200 N*m (2039 kgf*cm, 148 ft.*lbf), so perform the procedure with at least 2 people.

    Note

    Before performing these procedures, first cover the connectors and tube joints of the fuel tank vent tube sub-assembly with vinyl tape and then clean away any mud or other substances that may be adhering in order to prevent foreign matter from contaminating the fuel system.


    1. A01IPURE01
      Text in Illustration
      *1 Fuel Pump Gauge Retainer
      *a CORRECT
      *b INCORRECT
      *c SST (Claw)

      Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

      SST
      09808-14030   ( 09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050 )

      Note

      Install SST (claw) to the correct location.

    2. A01IQ1UE01
      Text in Illustration
      *a Center Point of Fuel Pump Gauge Retainer

      Adjust the position of SST (claw) so that the hole in SST (plate) for installing SST (handle) is in the center of the fuel pump gauge retainer.

    3. A01ISAFE01
      Text in Illustration
      *a SST (Plate)
      *b SST (Claw)
      *c SST (Bolt)
      A01ISM9 Press

      Press SST (claw) against the rib of the fuel pump gauge retainer and tighten SST (bolt).

    4. A01IQNRE01
      Text in Illustration
      *a SST (Handle)
      *b SST (Plate)
      *c Worker A
      *d Worker B
      A01ISM9 Hold Down
      A01ISER Slowly Rotate

      Install SST (handle) to SST (plate).

    5. To make sure SST does not separate from the fuel pump gauge retainer, one person should hold down the center of SST from above while at the same time both people slowly rotate SST (handle), and slowly loosen the fuel pump gauge retainer by approximately 90°.

      Note


      • Be careful not to apply excessive downward force to SST, as this may damage the fuel tank vent tube sub-assembly or fuel tank assembly.

      • Turning SST at an angle may cause it to slip off of the fuel pump gauge retainer, so make sure SST is horizontal when turning it.

      • To prevent damage to parts, do not turn SST too vigorously.

      • If SST slips off of the fuel pump gauge retainer, loosen SST (bolt) and install SST again.

    6. A01IOSRE01
      Text in Illustration
      *a SST (Handle)
      *b SST (Plate)
      *c Worker A
      *d Worker B
      A01ISM9 Press Down
      A01ISER Slowly Rotate

      While one person presses down to prevent the fuel pump gauge retainer and fuel tank vent tube sub-assembly from rotating together, the other person should slowly rotate SST (handle) and remove the fuel pump gauge retainer from the fuel tank assembly.

      CAUTION:

      Make sure not to pinch your hands with SST.

      Note

      If the fuel pump gauge retainer is turned while the fuel tank vent tube sub-assembly and fuel tank assembly are not fully engaged, the fuel tank vent tube sub-assembly will move with the fuel pump gauge retainer, and the fuel tank vent tube sub-assembly and the fuel tank assembly will both be damaged.

  8. REMOVE FUEL TANK VENT TUBE SUB-ASSEMBLY


    1. Remove the fuel tank vent tube sub-assembly from the fuel tank assembly.

      Note

      Make sure that the fuel sender gauge assembly arm does not bend.

    2. A01IUCYE03
      Text in Illustration
      *1 Gasket

      Remove the gasket from the fuel tank assembly.

  9. REMOVE FUEL SENDER GAUGE ASSEMBLY


    1. A01INV5

      Disconnect the fuel sender gauge assembly connector.

    2. Detach the wire harness clamp.

      Note

      Do not damage the wire harness.

    3. Release the lock as shown in the illustration and slide the fuel sender gauge assembly to remove it.