ПРОКЛАДКА ГОЛОВКИ БЛОКА ЦИЛИНДРОВ УСТАНОВКА

Note


  • Always be sure to check the tightening torque.

  • If the pressure lines are leaking after installation, they must be replaced.

  • Do not overtighten the pressure lines.


  1. SELECT CYLINDER HEAD GASKET


    1. Check the piston protrusions for each cylinder.


      1. Clean the cylinder block with solvent.

      2. Set the piston of the cylinder to be measured to slightly before TDC.

      3. A01IPC1E01
        Text in Illustration
        *a Measuring Tip
        *b Measuring Point
        *c Protrusion

        Using SST, place a dial indicator on the cylinder block and set the measuring tip as shown in the illustration.

        SST
        PZ4TB-04901-85

      4. Set the dial indicator at 0 mm (0 in.).

        Tech Tips

        Make sure that the measuring tip is perpendicular to the cylinder head gasket surface and piston head when taking the measurements.

      5. Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.

      6. Measure each cylinder at 2 places for a total of 8 measurements.

      7. For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

        Standard piston protrusion
        0.420 to 0.680 mm (0.0165 to 0.0267 in.)

        If the protrusion is not as specified, remove the piston sub-assembly and connecting rod sub-assembly and reinstall them.

    2. A01IQYNE01
      Text in Illustration
      *a Cylinder Head Gasket Hole
      A01ISM9 Front

      Select a new cylinder head gasket.

      New Installed Cylinder Head Gasket Thickness
      Cylinder Head Gasket Holes Specified Condition
      1 Hole 0.95 mm (0.0374 in.)
      2 Holes 1.05 mm (0.0413 in.)
      3 Holes 1.15 mm (0.0452 in.)

      Tech Tips

      Cylinder head gaskets have 1, 2, or 3 holes.


      1. Select the largest piston protrusion value from the measurements and then select a new appropriate gasket according to the table below.

        Cylinder Head Gasket Size
        Item Specified Condition
        Piston Protrusion 0.42 mm (0.0165 in.) or less 0.42 to 0.53 mm (0.0165 to 0.0208 in.) 0.53 to 0.68 mm (0.0208 to 0.0267 in.)
        Cylinder Head Gasket Holes 1 Hole 2 Holes 3 Holes

  2. INSTALL CYLINDER HEAD GASKET


    1. Place the cylinder head gasket in position on the cylinder block.

  3. INSTALL CYLINDER HEAD SUB-ASSEMBLY

    Note


    • Do not reuse the cylinder head bolts.

    • A01IRUE

      Make sure the ring pin shown in the illustration is not loose, deformed or otherwise damaged.


    1. Place the cylinder head sub-assembly on the cylinder head gasket.

      Note

      Be careful of the installation direction.

    2. A01ISZN

      Using an E10 "TORX" socket wrench, temporarily install the 5 bolts.

    3. Apply a light coat of engine oil to under the heads of the new cylinder head bolts.

      Note

      Do not reuse the cylinder head bolts.

    4. Temporarily install the new cylinder head bolts.

    5. Step 1:


      1. A01IT19E02

        Using an E18 "TORX" socket wrench, uniformly tighten the 10 cylinder head bolts in several steps in the sequence shown in the illustration.

        Torque:
        70 N*m  { 714 kgf*cm, 52 ft.*lbf }

      2. Mark the front of each cylinder head bolts head with paint.

      3. A01IT19E01

        Loosen the cylinder head bolts by 180° in the sequence shown in the illustration.

    6. Step 2:


      1. A01IT19E02

        Tighten the 10 cylinder head bolts in several steps in the sequence shown in the illustration.

        Torque:
        50 N*m  { 510 kgf*cm, 37 ft.*lbf }

      2. Retighten the cylinder head bolts by 120°.

    7. Step 3:


      1. Tighten the cylinder head bolts 120° further.

      2. Check that the paint marks are now at a 240° angle to the RH.

    8. A01ISZN

      Using an E10 "TORX" socket wrench, tighten the 5 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  4. INSTALL GLOW PLUG ASSEMBLY

    A01IUCDE01

    1. Using SST, install the 4 glow plug assemblies.

      SST
      PZ4TB-04910-68
      Torque:
      18 N*m  { 178 kgf*cm, 13 ft.*lbf }

    2. Connect the 4 connectors to the glow plug assemblies.

  5. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH


    1. A01IQJQE01

      Install the engine mounting insulator sub-assembly RH with the 4 bolts and 3 nuts.

      Torque:
      for bolt and nut A
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
      for nut B
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }

    2. Attach the clamp to connect the air conditioner tube and accessory assembly.

    3. Attach the 2 clamps to connect the suction pipe sub-assembly.

    4. Remove the jack.

  6. CONNECT RADIATOR RESERVOIR ASSEMBLY


    1. Connect the radiator reservoir assembly with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  7. INSTALL NO. 2 TURBO INSULATOR


    1. Install the No. 2 turbo insulator with the 3 bolts.

      Tech Tips

      Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.

  8. INSTALL EGR VALVE BRACKET


    1. Install the EGR valve bracket to the cylinder head sub-assembly with the 2 bolts.

      Tech Tips

      Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.

  9. INSTALL EXHAUST MANIFOLD

    Click here

  10. INSTALL CAMSHAFT AND NO. 2 CAMSHAFT

    Click here

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.