СИСТЕМА ECD (для клапана регулирования всасывания), Diagnostic DTC:P0617

DTC Code DTC Name
P0617 Starter Relay Circuit High

DESCRIPTION

While the engine is being cranked, the Starter Control (STA) signal is also sent to terminal STA of the ECM. The STA signal is used to increase the fuel injection volume mainly when starting the engine. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, this DTC is stored.

DTC No. DTC Detection Condition Trouble Area
P0617

STA signal is being input to ECM regardless of whether vehicle is in motion

(1 trip detection logic)

  • Starter relay circuit

  • Ignition switch

  • ECM
Related Data List
DTC No. Data List
P0617 Starter Signal

WIRING DIAGRAM

A01IRNTE04
A01IOGWE03

INSPECTION PROCEDURE

Note


  • When replacing the ECM, the ECM needs Registration and Initialization Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips


  • The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table Click here.

  • If this DTC is output, inspect the starter.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (STARTER SIGNAL)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

    4. Read the value displayed on the GTS when the ignition switch is turned to ON.

      OK
      Ignition Switch Positions Starter Signal
      ON OFF
      START ON
      Result
      Result Proceed to
      OK A
      NG (w/ Entry and Start System) B
      NG (w/o Entry and Start System) C

    A

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

    B

    CHECK HARNESS AND CONNECTOR Click here

    C

  2. INSPECT IGNITION SWITCH ASSEMBLY


    1. Inspect the ignition switch assembly Click here.


    NG

    REPLACE IGNITION SWITCH ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR


    1. Disconnect the ignition switch connector.

    2. Disconnect the ECM connector.

    3. Remove the ST relay from the No. 3 relay block.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H6-8 (ST2) or A76-36 (STA) - Body ground and other terminals Always 10 kΩ or higher

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

  4. CHECK HARNESS AND CONNECTOR


    1. Disconnect the power management control ECU connector.

    2. Disconnect the ECM connector.

    3. Remove the ST relay from the No. 3 relay block.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H70-2 (STA) or A76-36 (STA) - Body ground and other terminals Always 10 kΩ or higher

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

  5. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  6. REPLACE IGNITION SWITCH ASSEMBLY


    1. Replace the ignition switch assembly Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  7. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

  8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NEXT

    END