СИСТЕМА ECD, Diagnostic DTC:P3000, P3001

DTC Code DTC Name
P3000 Rail Pressure Correction Value is Equal or Higher than the Maximum Limit
P3001 Rail Pressure Raw Value is below Minimum Offset

DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the fuel quantity control valve to regulate the internal pressure to the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip.

This sensor outputs the voltage in proportion to the internal fuel pressure.

DTC No. DTC Detection Condition Trouble Area
P3000

Fuel pressure sensor feedback value exceeds upper limit for 0.1 seconds or more

(3 trip detection logic)

  • Open or short in fuel pressure sensor (common rail assembly) circuit

  • Fuel pressure sensor (common rail assembly)

  • ECM
DTC No. DTC Detection Condition Trouble Area
P3001

Fuel pressure sensor feedback value falls below lower limit for 0.1 seconds or more

(3 trip detection logic)

  • Open or short in fuel pressure sensor (common rail assembly) circuit

  • Fuel pressure sensor (common rail assembly)

  • ECM

WIRING DIAGRAM

A01IR66E53

INSPECTION PROCEDURE

Note

When replacing the ECM and/or injector assembly, the ECM needs Registration and Initialization Click here.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)


    1. Disconnect the fuel pressure sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C99-2 (PCR1) - C84-101 (PC) Always Below 1 Ω
      C99-3 (VC1) - C84-54 (VCS) Always Below 1 Ω
      C99-1 (E1) - C84-102 (E2S) Always Below 1 Ω
      C99-2 (PCR1) or C84-101 (PC) - Body ground Always 10 kΩ or higher
      C99-3 (VC1) or C84-54 (VCS) - Body ground Always 10 kΩ or higher
      C99-1 (E1) or C84-102 (E2S) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (VC VOLTAGE)


    1. Disconnect the fuel pressure sensor connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C99-3 (VC1) - C99-1 (E1) Ignition switch ON 4.5 to 5.5 V

    NG

    REPLACE ECM Click here

    OK

  3. REPLACE FUEL PRESSURE SENSOR


    1. Replace the fuel pressure sensor Click here.


    NEXT

  4. CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Read the DTCs.

      Result
      Result Proceed to
      No DTC output A
      DTC P3000 or P3001 B

    B

    REPLACE ECM Click here

    A

    END

  5. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  6. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

  7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NEXT

    END