СИСТЕМА ECD, Diagnostic DTC:P06B9, P06BA, P06BB, P06BC

DTC Code DTC Name
P06B9 Cylinder 1 Glow Plug Circuit Range / Performance
P06BA Cylinder 2 Glow Plug Circuit Range / Performance
P06BB Cylinder 3 Glow Plug Circuit Range / Performance
P06BC Cylinder 4 Glow Plug Circuit Range / Performance

DESCRIPTION

Refer to P052F Click here.

DTC No. DTC Detection Condition Trouble Area
P06B9

Either condition is met (3 trip detection logic):


  • Malfunction in part of glow plug controller assembly which outputs to No. 1 glow plug for 1.2 seconds or more

  • Glow plug controller assembly detects resistance malfunction in No. 1 glow plug for 1.2 seconds or more

  • Glow plug controller assembly

  • No. 1 glow plug

  • Open or short in No. 1 glow plug circuit
DTC No. DTC Detection Condition Trouble Area
P06BA

Either condition is met (3 trip detection logic):


  • Malfunction in part of glow plug controller assembly which outputs to No. 2 glow plug for 1.2 seconds or more

  • Glow plug controller assembly detects resistance malfunction in No. 2 glow plug for 1.2 seconds or more

  • Glow plug controller assembly

  • No. 2 glow plug

  • Open or short in No. 2 glow plug circuit
DTC No. DTC Detection Condition Trouble Area
P06BB

Either condition is met (3 trip detection logic):


  • Malfunction in part of glow plug controller assembly which outputs to No.3 glow plug for 1.2 seconds or more

  • Glow plug controller assembly detects resistance malfunction in No. 3 glow plug for 1.2 seconds or more

  • Glow plug controller assembly

  • No. 3 glow plug

  • Open or short in No. 3 glow plug circuit
DTC No. DTC Detection Condition Trouble Area
P06BC

Either condition is met (3 trip detection logic):


  • Malfunction in part of glow plug controller assembly which outputs to No. 4 glow plug for 1.2 seconds or more

  • Glow plug controller assembly detects resistance malfunction in No. 4 glow plug for 1.2 seconds or more

  • Glow plug controller assembly

  • No. 4 glow plug

  • Open or short in No. 4 glow plug circuit

WIRING DIAGRAM

A01IOVHE01

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - GLOW PLUG)


    1. Disconnect connectors of the glow plug controller assembly.

    2. Remove the glow plug connector from the glow plug.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      X1-4 (GL1) - X3-1 Always Below 1 Ω
      X1-1 (GL2) - X4-1 Always Below 1 Ω
      X1-6 (GL3) - X5-1 Always Below 1 Ω
      X1-5 (GL4) - X6-1 Always Below 1 Ω
      X1-4 (GL1) or X3-1 - Body ground Always 10 kΩ or higher
      X1-1 (GL2) or X4-1 - Body ground Always 10 kΩ or higher
      X1-6 (GL3) or X5-1 - Body ground Always 10 kΩ or higher
      X1-5 (GL4) or X6-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  2. REPLACE GLOW PLUG


    1. Replace the glow plug Click here.


    NEXT

  3. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Turn the ignition switch to ON and wait for 15 seconds or more [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NG

    REPLACE GLOW PLUG CONTROLLER ASSEMBLY Click here

    OK

    END

  4. REPLACE GLOW PLUG CONTROLLER ASSEMBLY


    1. Replace the glow plug controller assembly Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  5. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Turn the ignition switch to ON and wait for 15 seconds or more [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NEXT

    END